3500 System

Rotor Kit Motor Speed Control RK4

Pulse Frequency: 1 Hz to 20 kHz
Voltage Range: 5–30V peak
Analog Output: 4–20 mA
Speed Range: 0–20,000 RPM 
Accuracy: ±0.1% of reading
Resolution: 0.1 RPM 

Dynamic Pressure Monitor

3 wiretransducer :10 kΩ
2 wire:1.5 MΩ to 3.5 MΩ typical
Dynamicpressure:100 mV/psi (1.45 mV/mBar)
Output Impedance :550 Ω
3 wire:-24 Vdc

Rack Interface I/O Module

RIM I/O Module with Modem Interface
Voltage: 24V DC (±10%)
Consumption: ≤15W
Analog Inputs:4–20mA
Digital Inputs:24V DC dry contact
RS-485:Modbus RTU @ 115.2kbps max

Proximitor Seismic Monitor

Signal Accepts from:1 to 4 proximity
velocity or accelerationtransducer signals
Power consumption:7.7 watts, typical
Standard:I/O 10 kΩ
Output Impedance:550 Ω
Transducer Power Supply:-24 Vdc
Voltage Compliance:0 to +12 Vdc range acrossload

Aero GT Vibration I/O Module

Supply Voltage: 24V DC (±10%)
Power Consumption: <15W (typical)
Input Channels:2 independent channels
Signal Range:±10V (IEPE), 4–20mA (Velocity)
Sampling Rate:Up to 100 kHz per channel
Frequency Response:0.5 Hz – 20 kHz (±3dB)
Dynamic Range:100 dB (typical)
ADC Resolution:24-bit
Analog Output:4–20mA

3500 SYSTEM CHASSIS RACK

02 12-inch Mini-Rack (7 module slots)
04 Panel Mount Option, Mini-Rack
00 None
00 None
01 CE
Mini-rack. 12-inch rack 
with seven available module slots

Low Voltage DC PIM

114M5335-01 Low Voltage DC PIM
Input Voltage:10-30V DC
Input Signal:LVDT/RVDT (1-5V RMS, 2.5-10kHz)
Output Signal:4-20mA (fault = 3.8mA or 21mA)
Accuracy:±0.25% FS

Half-Height Future Expansion Faceplate

Half-Height Modules
3500 Series Rack Can Contain One or Two Power Supplies
(3) Versions Manufactured

19-inch Rack

01 19-inch Rack (14 module slots)
02 Rack Mount Option, Full-Size Rack 
(mounts to19-inch EIA Rack)
01 CSA/NRTL/C (Class 1, Division 2) 
00 None

Low Voltage DC PIM

Inputvoltage:20 to 30 Vdc
For all power supply options, 
anunder-voltage does not harmthe supply or the PIM
An over-voltage causes the fuseto open on the PIM
14M5330-01 Low Voltage DC Power Supply

Hazardous Gas Sensor

DETECTION SENSOR
HAZARDOUS GAS
REVISED TO 350800-01-006-00
15 MV / % LEL SENSITIVITY
FLAMEPROOF AND IP66

I/O Module Cover

Model Number:128031-01D
Type:I/O Module Protective Cover
Color:Typically black or gray

Recip Rod Position Monitor

Signal :Accepts from 1 to 4 proximityprobe signals
InputImpedance:10 kΩ
Peak-Peak filter Fixed:1 Hz to 600 Hz
Gap filter: -3 dB at 0.09 Hz
Average pistonposition Fixed:1 Hz to 600 Hz
Average Gap:-3 dB at 0.09 Hz

System Rack

Full-size rack
01 19-inch Rack (14 module slots)
00 None
00 None
01 CE

Proximitor/Seismic I/O Module

Radial Vibration
Thrust Position
Differential Expansion
Shaft Absolute
Eccentricity
Acceleration
Velocity

Process Variable Monitor

+/-10 Vdc I/O : -10 Vdc to +10 Vdc
4-20 mA Barrier I/O:4-20 mA DC
Voltage Compliance:13.66 V
Isolation:500 Volts
Power Consumption:7.0 Watts, typical
Accuracy:Within ±0.33% of full-scaletypical, ±1% maximum

Velocity Monitor

Impulse Acceleration
Acceleration 2
Recip Velocity
Low Frequency Recip Velocity
Signal:Accepts from 1 to 4 proximityprobe signals.
Special inhibit:Contact closure5 Vdc @ 390μA typical
Powerconsumption: 7.7 watts, nominal

Hydro Monitor

Powerconsumption 7.7 watts, typical
Multimodepositive inputI/O 50 kΩ
Direct filter0.104 Hz to 500 Hz
Rotor speed is 25 to 1,500 cpm.
Gap filter -3 dB at 0.05 Hz
Direct filter -3dB at 1.2 Hz

High Voltage DC PIM

High Voltage DC PIM
1.9/7.5 AMP
95-125 VAC
190-250 VAC
47/63 HZ

Temperature Monitor

Accepts from 1 to 6 RTD or TC transducersignals
Greater than 3 MΩ for each lead input.
TC Option: Nominal consumption of 6.3watts.
RTD Option: Nominal consumption of 5.6watts

Temperature Module

Model: 3500/61
Part Number: 133811-02.
Description: 16-Channel Temperature Monitor Module
RTDs:2-wire, 3-wire, or 4-wire Pt100
RTD Excitation Current: 1 mA
ADC Resolution: 16-bit
Accuracy RTD: ±0.5°C (±0.9°F) typical
Programmable Alarms: Up to 4 per channel 

I/OModule

TRANSIENT DATA INTERFACE MODULE
3500
100Base-FX (Fiber Optic) 
I/OModule

VGA Display Unit

Powerconsumption:4.6 watts max
High-speednetwork:Monitor status, data andvalues
RS232 port:Touch controller data
Front Port:24 Vdc Power
Power +24Vdc ± 6%:4.7 watts max 
Input range :22.5 to 25.5 Vdc input 
VGA inputs:Video image
RS232 inputs:Touch screen control data 

Aero GT Vibration I/O Module

12659901
VIBR I/O MODULE
Aero GT I/O Module Internal Terminations

Proximitor ET BlockEuro Style Connectors

125808-01 Proximitor ET BlockEuro Style Connectors
Signal :Accepts from 1 to 4 proximitytransducer signals
Power consumption :7.7 Watts, typical
Standard I/O: 10 kΩ
Output Impedance:550 Ω
Transducer Power Supply:-24 Vdc
Gap filter:-3 dB at 0.09 Hz
Smax : 0.125 to 15.8 times runningspeed