PowerFlex 753 AC Drive
with Embedded I/O
Standard Protection
Forced Air, AC Input with DC Terminals
Flange Type, 104 Amps, 55kW ND
45kW HD, 400 VAC, 3 PH, Frame 5
Filtered, CM jumper installed (preferred)
DB Transistor, Blank (No HIM)
PowerFlex 753 AC Drive
with Embedded I/O
Standard Protection
Forced Air
AC Input with DC Terminals
Flange Type
37 Amps
18.5kW ND
15kW HD
400 VAC
3 PH, Frame 3
Filtered, CM jumper installed (preferred)
DB Transistor, Blank (No HIM)
PowerFlex 753 AC Drive
with Embedded I/O
Standard Protection
Forced Air, AC Input with DC Terminals
Flange Type, 22 Amps, 11kW ND
7.5kW HD, 400 VAC, 3 PH, Frame 2
Filtered, CM jumper installed (preferred)
DB Transistor, Blank (No HIM)
Series:ControlLogix
Module Type:Fast Digital DC Isolated Input
Inputs:16 Individually Isolated
Input Voltage:12-24 Volts DC
Operating Voltage Range:10-30 Voltage DC
Input Delay Time:14 microseconds plus selected filter time
Current Draw (5.1 Volts):275 milliamps
Current Draw (24 Volts):3 milliamps
Power Dissipation:3.8 Watts
Series:POINT I/O
Module Type:Analog Output Module
Outputs:4 Single Ended
Data Format:Signed Integer
External DC Supply Current:220 mA
Output Signal Range:4 to 20 mA, 0 to 20 mA
Output Resolution:16 bits across 0 to 21 mA
Conversion Type:Digital-Analog
Conversion Rate:20 microseconds
Resolution:14 bits
Module Width:Single Slot
Compatible controllers:SLC 5/02 or later
Pass through: Supported
Communication Port:One (1) DeviceNet
Data Transfer speed:125Kbps
Linear Plug:1787-PLUG10R
Indicators:Mod/Net Status - red/grn; I/O Status - red/grn
Mounting:DIN Rail; Panel Mounting
Storage Temperature:-40 to 85 C (-40 to 185 F)
Series:Stratix Managed Switches
Part Number:1783-MX08T
Relative humidity:5% to 95%
Connector Type:10/100 Base-T Copper Ethernet Port
Enclosure:Open type
Number of Ethernet Copper ports:8
Operating Temperature:-40 to 60 degrees Celsius
Network Type:Ethernet
Ethernet nodes:8 Nodes
No. of Task:32 Task
No. of Program per Task:100
No. of Embedded Inputs:(16) 24 VDC
Module Type:Processor Module
Communication:Ethernet
Input Power:24 Volts DC
Memory:512KB
Communication Cable:6 Point
Shipping Weight:3 pounds
Range of product:Altivar
Product or component type:Communication module
Communication port protocol:Profibus DP V1
Electrical connection:1 female connector SUB-D 9
Transmission rate:9.6 kbps...12 Mbps
Elliptical clamp shape improves access
to earth cables and straps up to 50 mm
Low maintenance flat jaw interface
Measures ground resistance from 0.05 Ω to 1500 Ω
Measures true RMS ground leakage current from
0.5 mA rms to 35 A rms
CAT IV 600 V safety rating
Backlit LCD display
Application Memory:4 MB
Safety Memory:2 MB
Non-volatile memory:2GB via 1784-SD2
Local I/O modules:31 I/O modules
Communication Ports:1 Type B 2.0
Full-Speed USB and 2 Ethernet/IP Ports
Communication rate, Ethernet:10 Mbps / 100 Mbps / 1 Gbps
User Memory:4 MB + 2 MB safety
Ports:2 Ethernet
Range of Product:Modicon Premium Automation platform
Product or Component Type:Double-format PL7 processor
Software Designation:PL7 Junior/Pro
Number of racks:16 4/6/8 slots/8 12 slots
Discrete I/O processor capacity:1024 I/O
Analogue I/O processor capacity:128 I/O
Number of application specific channel:32
MICROMASTER 440
without filter 380-480 V
3 AC +10/-10% 47-63 Hz
constant torque 15 kW
overload 150% 60 s,
200% 3 s square-law torque 18.5 kW
520x 275x 245 (HxWxD)
degree of protection IP20 ambient
temperature -10+50 °C
without AOP/BOP
MICROMASTER 440
without filter 380-480 V
3 AC +10/-10% 47-63 Hz
constant torque 5.5 kW
overload 150% 60 s,
200% 3 s square-law torque 7.5 kW
245x 185x 195 (HxWxD)
degree of protection IP20
ambient temperature -10+50 °C
without AOP/BOP
Max number of mountable I/O modules:8
Number of mountable Power suply modules:2
S Standard type
0 19-inch rack-mounted
BASE MODULE
STYLE S1
STANDARD TYPE
19 INCH RACK
DIN MOUNT
(92F306027)
Interface:RS-422/RS-485 (2 ports)
How connected:Multipoint
How communicates Half-duplex/Full-duplex
How synchronizes Start-stop synchronization
Transmission code ASCII/binary
Character length:7/8 bits
Stop bit :1/2 bits
Parity check None/even/odd
Transmission distance Maximum:1200 m
Current consumption:500 mA
Number of input channels:12, isolated
Allowable input voltage:±5 V
Between input and system: 1500 V AC for 1minute
Power ON :2 MΩ or more
Power OFF: 2 MΩ or more
Allowable total resistance of signalsource plus wiring:40 Ω or less
Effect of allowable signal source resistance (1000 Ω): ±20 μV
Measurement current:1 mA
Temperature drift:Max. ±30 ppm/°C
Maximum current consumption:450 mA (5 V DC)
Allowable input voltage ±5 V.
Withstanding voltage :1500 V AC for 1minute
Power ON 2 MΩ or more
Power OFF 2 MΩ or more
Accuracy ±0.03% of full scale (for 0 to 400 Ω)
Allowable total resistance of signalsource plus wiring:40 Ω or less
(wiring resistance per wire)
Temperature drift:Max. ±30 ppm/°C.
Maximum current consumption:450 mA (5 V DC)
Number of input channels:32
Rated input voltage:24 V DC
Input ON voltage:18 to 26.4 V DC
Input OFF voltage:5.0 V DC or less
Input current (at rated input voltage):4.1 mA±20 % / channel
Instantaneous allowable maximum input voltage:30.0 V DC
Input response time:8 ms or less
Minimum ON detection time:20 ms
Maximum ON/OFF cycle:25 Hz
Maximum current consumption:500 mA (5 V DC)
Number of output channels:64
Rated applied voltage:24 V DC
Load voltage:24 V DC, 100 mA
Field power supply voltagerange:20.4 to 26.4 V
Output ON voltage maximumvalue:2 V DC
Leak current maximum valuewhen output OFF:0.1 mA
Output format:Current sink
Number of input:channels16, non-isolated
Input signal:4 to 20 mA
Allowable input current/voltage:27 mA
Accuracy:±0.1% of full scale
Data refresh cycle:10 ms
Input step response time:100 ms
Transmitter power supply:22.8 to 26.4 V
Setting of 2-wire or 4-wiretransmitter
For each channel by setting pin
Power Requirements 5 VDC, ± 5% a
USB Annunciator Keyboard: 300 mA (max)
Output Impedance: 1200 Ohms Nominal
Nominal Level: 0.437 to 0.133
Peak to Peak Amplitude, Vpp: 0.872
Operating Temperature 0 to 40°C (32 to 104°F)
Storage Temperature -40 to +70°C (-40 to 158°F)
Humidity range, storageand operating:
20% to 80%, non-condensing
Product:X-Gateways
Data Rate:100 Mb/s
Number of Ports:2 x RJ45
Interface Type:Ethernet, USB
Supply Voltage - Min:24 V
Supply Voltage - Max:24 V
Packaging:Bulk
Brand:HMS Networks
Safetybus Power 0.85 load units
Number of Inputs 16, common power return
Vibration10 to 55 Hz: ±0.15mm
Turn-On Voltage (default) > 12 Vdc
Voltage: 15 to 80 VDC
Current:450 mA, maximum
Interface:RS-422/RS-485 (2 ports)
How connected:Multipoint
How communicates Half-duplex/Full-duplex
How synchronizes Start-stop synchronization
Transmission code ASCII/binary
Character length:7/8 bits
Stop bit :1/2 bits
Parity check None/even/odd
Transmission distance Maximum:1200 m
Current consumption:500 mA
Number of input channels:32
Rated input voltage:24 V DC
Input ON voltage:18 to 26.4 V DC
Input OFF voltage:5.0 V DC or less
Input current (at rated input voltage):4.1 mA±20 % / channel
Instantaneous allowable maximum input voltage:30.0 V DC
Input response time:8 ms or less
Minimum ON detection time:20 ms
Maximum ON/OFF cycle:25 Hz
Maximum current consumption:500 mA (5 V DC)
Number of input channels:8, isolated channels
Input frequency:0 to 10 kHz
Minimum input pulse width:40 μs
Shunt resistance Select from:OFF/200/500/1000 Ω
Pull-up resistance:68 kΩ (12 V DC or 24 V DC
Data refresh cycle:2 ms
Filter function Can select a filter that eliminates chattering
Transmitter power supply
Can select:24 V DC/12 V DC.
Number of output channels:64
Rated applied voltage:24 V DC
Load voltage:24 V DC, 100 mA
Field power supply voltagerange:20.4 to 26.4 V
Output ON voltage maximumvalue:2 V DC
Leak current maximum valuewhen output OFF:0.1 mA
Output format:Current sink
Number of input:channels16, non-isolated
Input signal:4 to 20 mA
Allowable input current/voltage:27 mA
Accuracy:±0.1% of full scale
Data refresh cycle:10 ms
Input step response time:100 ms
Transmitter power supply:22.8 to 26.4 V
Setting of 2-wire or 4-wiretransmitter
For each channel by setting pin
Allowable input voltage ±5 V.
Withstanding voltage :1500 V AC for 1minute
Power ON 2 MΩ or more
Power OFF 2 MΩ or more
Accuracy ±0.03% of full scale (for 0 to 400 Ω)
Allowable total resistance of signalsource plus wiring:40 Ω or less
(wiring resistance per wire)
Temperature drift:Max. ±30 ppm/°C.
Maximum current consumption:450 mA (5 V DC)
Outputs per module 2 channel single-ended, nonisolated
Output current 0…20 mA
Resolution 12 bits, 1/4096 max, 4.88 µA/bit
Converted data Binary data 0000 to 0fff (max scale)
Conversion time 2 ms/channel
Overall accuracy 0.2% Full scale @ 0…55 °C
Calibration None required
Allowable external output load resistance600 Ω max
Manufacturer: Alfa Laval
Model Number: 3183052091
Product Name: VCU-160 Module
Application: HVAC systems
Input Voltage: Typically 24V DC or 230V AC
Operating Temperature Range: -20°C to +55°C
Protection Rating: Typically IP20
Manufacturer: Alfa Laval
Model Number: 3183034171
Product Name: Heatpac Control Module
Application: HVAC systems
Input Voltage: Typically 24V DC or 230V AC
Operating Temperature Range: -20°C to +55°C
MICRONET SIMPLEX LV DISCRETE FTM
INPUT VOLTAGE RATING: 27.4 AMP 18-32 VDC
OUTPUT VOLTAGE RATING: 16 AMP 24VDC
POWER SUPPLY INPUT: (18 TO 32) V (DC)
SIGNAL TO ACTUATOR: 0 TO 200 MA
NETWORK ISOLATION: 0–60 HZ: 1000 VRMS
Input Voltage:Typically 24 VDC
Power Consumption:Around 25 W
Operating Temperature Range:Typically -20°C to 60°C
Storage Temperature Range:-40°C to 85°C.
Relative Humidity:5% to 95% non-condensing.
Input Voltage: Typically 24 V DC
Operating Temperature Range:
Typically -30°C to +70°C (-22°F to 158°F)
Storage Temperature Range:
-40°C to +85°C (-40°F to 185°F)
Voltage at min. GAP:−1.6 V
Voltage at max. GAP:−17.6 V
Dynamic range:16 V
Output impedance:500 Ω
Short-circuit current:45 mA
Voltage:−20 to −32 V*
Current:−13 mA ±1 mA (−25 mA max.)
Type: Optical ESB Bus Repeater Module
Bus System: ESB
Connector Type: SC or LC connectors
Operating Voltage: Typically 24 V DC
Operating Temperature Range: -10°C to 60°C (14°F to 140°F)
Power Consumption: Typically low, around 3-5W
Processor:Typically powered by a PowerPC 7448
Memory:512 MB to 2 GB DDR2 RAM
CompactFlash or Solid-State Drive (SSD)
Bus Speed: 40 MHz
Voltage: Typically 5V DC
Power Consumption: 20-50W
Operating Temperature: Typically 0°C to 70°C (-40°C to +85°C)
Storage Temperature: Typically -40°C to +85°C.
Humidity: 5% to 95% relative humidity
Series:POINT I/O
Module Type:Serial Interface Module
Key Switch Position:2
Voltage Range:10-28.8 volts DC
Supply Voltage:24 volts DC nominal
Supply Current:15mA at 24 volts DC
Communication port protocol:Modbus Plus
Communication port support:RS232
Modbus Plus bridges and repeaters
characteristics:Programmable
Bridge
Mounting support:Panel Enclosure
Number of port:4
Rated supply voltage:115...220 V AC 24 V DC
Product Description:Serial Synchronous Interface (SSI) module
SSI Channels:1
Product Family:1734 POINT I/O
Supply Voltage:10-28.8 Volts DC
Part Number:1734-SSI
POINTBus Current:110 milliamps
Power Dissipation:0.94 Watts
No of SSI channels:One (1) SSI port
Supply current :110mA @ 24V dc
Operating Temperature:-20 to 55oC (-4 to 131oF)
Storage Temperature:-40 to 85°C (-40 to 185°F)
Linear Measurement Range 2 mm (80 mils)
Initial Air Gap 0.5 mm (20 mils)
Incremental Scale Factor (ISF)
ISO: 8 V/mm (203.2 mV/mil) ± 5%@
temperature range 0 to 45°C(+32 to +113°F)
Deviation from best fit straight line(DSL)
± 0.025 mm (± 1 mil)@
temperature range 0 to 45°C(+32 to +113°F)
Minimum Shaft Diameter 25 mm (0.79”)
Part Number/Catalog No.:1734-CTM
Series:POINT I/O
Module Type:Terminal Module
Isolation Voltage:250 Volts Continuous
Field Power Supply:1-28.8 Volts DC or 12/240 Volts AC
Field Power Supply Current:4 amps/module
Overvoltage protection, max:± 30V DC
Overcurrent protection, max:±30 mA
Open circuit detection time:2 seconds
Module Keying:Electronic
Number of Inputs:8 Differential Inputs
Number of Outputs:N/A
Voltage Category:N/A
Input Voltage Range:+/- 10 Volts, 0-10 Volts, 0-5 Volts
Output Voltage Range:N/A
Power Dissipation:2.1 Voltage Mode and 2.4 Current Mode
Enclosure Type:None (Open Style)
Product Type: Safety Relay
Model Number: 440R-GL2S2P
Series: Guardmaster
Input Voltage: 24V DC
Voltage Tolerance: -15% to +10%
Current Consumption: Approx. 200mA
Power Consumption: Typically 4.8W
Relay Output Type:
Safety Outputs: 2 NO
Auxiliary Outputs: 1 NC
Product Line:SMC-Flex
Part Number/Catalog No.:150-F43NBD
Bulletin Number:Solid-State Controller
Controller Ratings:480 Amps,
400 Horsepower at 460 Volts AC
Input Line Voltage:200 to 460 Volts AC
Control Voltage:120 / 240 VAC
Rated Voltage:500 to 575 Volts AC
SCALANCE XB008G
UNMANAGED INDUSTRIALETHERNET SWITCH
FOR 10/100/1000MBIT/S
W. 8 X 10/100/1000MBIT/S
RJ45- ELECTRICALPORTS
FOR ESTABLISHING SMALL STAR- ANDLINE
TOPOGRAPHIES
LED-DIAGNOSTICS, IP20
DP/AS-Interface F-Link
gateway PROFIBUS DP/AS-i
for safety-oriented data transmission
from ASIsafe to PROFIBUS-DP-PROFIsafe
Master profile M3/M4 according to
AS-i specification V3.0
degree of protection IP20
spring-loaded terminals
Model Number: A5E00063020
Type: Switching Power Supply
Input Voltage: 120/230V AC (auto-ranging)
Input Frequency: 47-63 Hz
Output Voltage: 24V DC
Output Current: Insert specific current, 5 A
Output Power: Insert specific power 120 W
Efficiency: Up to [insert specific efficiency, 90%
Model Number: 6DR5220-0EM21-0AA0
Product Family: SIPART PS2
Input Signal: 4 to 20 mA
Operation Type: Double-acting for bidirectional control
Pneumatic Connection Thread: 1/4 inch NPT
Enclosure Material: Durable polycarbonate housing
SIMATIC S7-300
CP 340 COMMUNICATION PROCESSOR
backplane bus 5 V DC, max.:220 mA
Power loss, max.:0.85 W
Transmission rate, min:2.4 kbit/s
FB length in RAM, max.:2 700 byte
Model Number: S79220-A3919-F000-01
Input Voltage: 24V DC
Power Consumption: < 10W (energy-efficient design)
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Storage Temperature: -20°C to 60°C (-4°F to 140°F)
Humidity Range: 10% to 90%
Ethernet: 10/100 Mbps (RJ45 connector)
RS-485: For connecting peripheral devices
