Output Channels 32
Output Type Source
Load Voltage 15 30 VDC Maximum
On-State Voltage 24 V (typ), load current @ 0.5A
Off-State Leak Current 5.0 µA (max)
Turn-On/Turn-Off Time 10 ms (max)
Inputs per module:32 (sinking)
Input Voltage Range:10 VDC to 32 VDC
Peak Voltage:32 VDC
AC Frequency: N/A
ON Voltage Level:9.5 VDC minimum
OFF Voltage Level:3.5 VDC maximum
Input Impedance:6.9 K ohms nominal
Minimum ON Current:1.0 mA
Maximum OFF Current:0.7 mA
Approvals: UL, CSA; FM pending
Type: CC 600 World 4 × 2.5 mm2
Bus bar side: 2 pole Squeeze To
Release type: D-TAB-200-STR
IO chassis side: FM5W5 S (female)
housing: low profile, 90°
The red wire represents the +24Vdc
The black wire represents the 0Vdc
Approvals: UL, CSA; FM pending
Housing type: 2 pole socket block
Weidmuller BLZ 5.08/2F
Crimp pin type: Weidmuller
DFFC 1.5-2.5 SN E
POWER BUSBAR MAX.200A 24/48/110VDC,150CM
Nominal Voltage:24 Vdc, 48 Vdc, 110 Vdc
Max Current:200 A continuous
Length:1,500 mm (150 cm)
Bus Sections 10 sections 152.4 mm each
Approvals:UL, CSA, FM‑pending
Power Supply Inputs:Dual 5V DC (5V-1 and 5V-2)
Power Consumption:0.05 A per 5V input rail
Chassis Width:482.6 mm (19 inches)
Operating Temperature:0°C to +50°C
Storage Temperature:-40°C to +70°C
Relative Humidity:5% to 95% non-condensing
Form Factor: 19-inch standard rack width
Slot Capacity: 21 slots for I/O module
Voltage: 24 V DC (±10%)
Humidity: 5–95% RH (non-condensing).
Vibration: 5–500 Hz, 2 g RMS (IEC 60068-2-6).
Shock: 30 g peak, 11 ms
Supply Voltage:24 V DC ±10%
Power Consumption:≤5 W
Isolation :500 V AC
I/O Channels:Likely 8–16
Function:Fieldbus interface or signal conditioning
Status:Discontinued
Voltage: Typically 24 VDC (±10%)
Power Consumption: <5–10 W
Digital Inputs: 8–16 channels
Analog Inputs: 4-20 mA/0-10 V
Temperature Range: -20°C to +70°C
Data Rate:31.25 kbit/s
Power Supply:24 V DC (via controller backplane)
Power Consumption:Typically 0.8 W per channel
Isolation:500 V AC
RUN (Green): Module operation
COM (Green/Yellow): Communication status
ERR (Red): Fault indication
Model SAI143
Number of input channels 16 channels module isolation
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C
Withstand voltage 1.5 kV AC
between input signal and system for 1 minute
Support PRM Available (SAI143-H)
Input Voltage:380–480 V AC
DC Link Voltage:540–650 V DC
Auxiliary Voltage:24 V DC
Product Line:ABB ACS800 Industrial Drives
Isolation Voltage:2.5 kV AC
Memory Size:5032 kB
Memory Type User Data:RAM
Controller Processing Time:0.00002 ms
Number of Digital Inputs:12
Number of Digital Outputs:8
Number of Digital Configurable I/Os:2
Input Voltage Type:DC
Output Voltage (Uout):24 V DC
Output Current:0.5 A
Degree of Protection:IP20
Rated Voltage (Ur):24 V DC
Supply Voltage:20.4 … 28.8 V DC
Input Voltage:200–480 V AC
DC Link Voltage:280–650 V DC
Auxiliary Voltage 24 V DC
PWR (Green): 24V OK
RDY (Yellow): Drive ready
ERR (Red): Fault detected
Isolation Voltage:2.5 kV AC
Voltage Rating:1200 V
Current Rating:900 A
Technology:Trench-gate IGBT4
Collector-Emitter Sat.:VCE(sat): 1.75 V (typ.)
Short-Circuit Withstand:10 μs
Isolation Voltage:4.5 kV RMS
Configuration:Single IGCT
Voltage Rating:4500 V
Current Rating:1200 A
Critical dv/dt:1000 V/μs (min.)
Isolation Voltage:10 kV RMS
Mounting Force:35–45 kN
Function:32-Channel Analog Input Module
Voltage: ±10 V DC, 0–10 V DC
Current: 0–20 mA, 4–20 mA
Resolution:15 bits + sign
Accuracy:±0.1% of full scale @ 25°C
Update Time:8 ms (all channels)
Common-Mode Rejection:>120 dB @ 50/60 Hz
Overvoltage Protection:±35 V DC
Power Supply:24 V DC
LOGIC CONTROLLER
32 CHANNELS
18-30 VDC
2 VDC
OUTPUT RATING: 0.01 A MINIMUM
AT 24 VDC 1.0 A MAXIMUM
24 VDC CONTINUOUS
SURGE: 2.5 A PER CHANNEL
ISOLATION: 1K VDC
10 MA PER CHANNEL
Power Supply: Typically on 24V DC
Input Voltage: Typically 24V DC for digital inputs
Output Voltage: Usually 24V DC.
Operating Temperature: Typically between 0°C and 55°C
Storage Temperature: Typically ranges from -20°C to 70°C
Humidity: Typically rated for 5% to 95%
Channels: 20 single-ended channels
Voltage: ±10 V DC
Current: 0–20 mA, 4–20 mA
Voltage Inputs: >1 MΩ.
Current Inputs: 250 Ω
Noise Rejection: >80 dB (50/60 Hz)
Channel-to-Backplane: 1,500 V AC RMS
Data Throughput: Up to 10,000
RAM: 512 KB
Voltage: +5V DC
Consumption: 10 W (typical)
Isolation:1500V AC
Fiber optic: Up to 4 km
Max Nodes: Up to 250 devices per loop
Detection Range:Up to 40 meters
Response Time:< 3 seconds
Supply Voltage:24 V DC
Power Consumption:4–8 W (DC)
Relay Contacts: 2× SPDT
Analog Output: 4–20 mA
