ALL MANUFACTURERS

VME SERVO CARD

RAM: 64–128 MB SDRAM
Non-Volatile Storage: 16–32 MB Flash
Channels: 4–8 channels
Signal Type: ±80 mA current output 
Resolution: 16-bit DAC.
Accuracy: ±0.1% FS (Full Scale).
Update Rate: 1–10 kHz 

Discrete Input Terminal Board

Input Channels:32 optically isolated inputs
Input Type: 24–125V DC
Voltage Range:24V DC 
Input Current :5–15mA per channel
Isolation :1500V AC
Response Time:≤10ms (ON/OFF)
Power Supply:+5V DC

Phase Logic Interface Board

Input Channels:3-phase voltage
Voltage Range:0–150V AC
Frequency Range:45–65Hz 
Accuracy:±1% of full scale 
Response Time:<2 cycles
Isolation:2500V AC 
Power Supply:+5V DC

DRIVE CPU BOARD

DRIVE BOARD
PRIMARY DRIVE CONTROLLER
MARK V
32-bit microprocessor
EPROM (Firmware storage)
RAM
Communication ICs
I/O interface circuitry

INTERFACE COMMUNICATION CARD

PROGRAMMER MODULE
INTERFACE COMMUNICATION CARD
MARK 5
TURBINE CONTROL
MULTI INPUT/ OUTPUT

Emergency Overspeed Board

Supply Voltage:24V DC ±10% 
Power Consumption:7 W (idle), 10 W (max)
Isolation:1500V AC 
MPU Signal Range:10–250 V RMS
Processor:3× 32-bit DSPs

Emergency Overspeed Board

PC BOARD
EMERGENCY OVERSPEED BOARD
MARK V
Supply Voltage:24V DC ±10% 
Power Consumption:8 W 
Isolation:1500V AC 

I/O Engine CPU Board

DRIVE BOARD
PROCESSOR CARD
DAUGHTER BOARD
UC2000
MARK V

UC2000 Motherboard

CIRCUIT BOARD ASSY
DS200UCIAG1A
Series:Mark V
Part Number:DS215UCIAG1AZZ05A
Functional Description:UC2000 Motherboard
Functional Acronym:UCIA
PCB Coating:Normal Coating
Assembly Type:DS215 Special Assembly

Gate Distribution and Status Board

Supply Voltage: +24 V DC (±10%) 
Power Consumption: ≤10 W
Isolation Voltage: 2500 V AC
Voltage: +15 V / -10 V 
Response Time: ≤1 μs for fault detection.

Exciter HS Relay Driver Board

Supply Voltage: +24 V DC
Power Consumption: ≤15 W 
Isolation Voltage: 1500 V AC
Voltage Range: 24–125 V DC
Current Rating: Up to 5 A per channel
Switching Speed: ≤10 ms 

Protective Termination Expander Board

PC BOARD
EOS PRINTED CIRCUIT BOARD
MARK 5
Input Voltage:24 VDC ±10%
Power Consumption:8W (typical)
Isolation:1500 VAC
Digital Inputs :24VDC

RXi Controller

RXI CONTROLLER / PACSYSTEMS
HIGH PERFORMANCE DISTRIBUTED IO
PROGRAMMABLE
REQUIRES ICRXIACCIDM001A

Common Analog I/O Board

Series: Mark V
Product Type: Terminal Board
Input Channels: 8 Analog Inputs
Input Resolution: 12-bit / 16-bit
Output Type: Voltage (0-10V, ±10V)
Output Resolution: 12-bit / 16-bit
Input Type: Voltage (0-10V, ±10V)
Communication Protocol: RS-485
Power Supply: 24V DC ±10%, < 5W
Isolation: 1500V

Simplex Trip Board

TRIP CONTROL CARD
PC BOARD SDCC MARK V SYSTEM
Analog Trip Signals: 4–20 m
Digital Trip Signals: 24 VDC
Aux Relay (K2): Alarm/status outputC
Resolution: 0.1% of setpoint
Accuracy: ±0.25% FS
Voltage: +24 VDC (±10%)
Consumption: 15 W (max)

DOS DUP Processor Board

PC BOARD
MARK 5 SERIES
TURBINE AND GAS CONTROL BOARD
WITH ON-BOARD MEMORY
MULTI-INPUT/OUTPUT

Power Connect Card

Series: EX2000
Microprocessor: Intel Ultra Low Voltage Celeron 650 MHz
Operating System: QNX Neutrino
Operating Temperature: 0 to 60°C
Product Type: Power Connector
Analog Input current: 240 V rms
DC Bus Voltage: 125 VDC
Auxiliary Voltage: +15 VDC

Single Board Computer

VME-7807 Series 
SINGLE PCB BOARD 
PROCESSOR: 1.8GHZ PENTIUM M DDR 
SDRAM: 1 GB L2 CACHE: 2MB 
FLASH: 512 KB 1101.10 
FRONT PANELSCAN DISK 2GBITES

Vibration Input Terminal Board

Series:Mark VIe Speedtronic
Part Number:IS200TVBAH2A
Functional Acronym:TVBA
Functional Description:Vibration Input Terminal Board
PCB Coating:Conformal Coating
Functional Revision 1:B

RX3I PROFINET SCANNER MODULE

RX3I PROFINET SCANNER MODULE
10/100/1000 WITH FOUR PORTS
1.2AMP @ 3.3VDC
1.1AMP @ 5 VDC
SINGLE SLOT

Terminal block

I/O BASE
BARRIER STYLE
2 TIER BOX TERMINAL

Terminal block

I/O BASE
BARRIER STYLE
2 TIER BOX TERMINAL

Thermocouple Input Module

ANALOG INPUT MODULE
THERMOCOUPLE
8POINT
INDEPENDENT THERMOCOUPLE OR MULTIVOLT INPUTS
50/60HZ

small form-factor pluggable scanner module

Type:Scanner module
Speed:100 Mbps
Material:Multi-mode fiber (MMF)
Length:2 Kilometers
SD Card:Supported
Power:3.3 to 5 Volts
Port Connectors:Two RJ-45 and two SFP cages.
LED Indicators:Yes

Terminal board

Series: GE Mark VIe Series
Input Voltage: 24 V DC (±10%)
Power Consumption: ≤8 W 
Voltage Range:0–30 V DC or 0–120 V AC
Range: 0–10 V DC, 4–20 mA
Resolution: 16-bit ADC
Type: Form-C contact relays (1 A at 30 V DC)
Operating Temperature: -40°C to +70°C
Relative Humidity: 5–95% (non-condensing)