ALL MANUFACTURERS

Gate Driver Board

Input Voltage Range: 15-30V DC 
Output Drive Voltage: +15V/-8V
Peak Output Current: ±20A 
Isolation Voltage: 2500V AC 
Propagation Delay: <100ns
Compatible IGBTs: 1200V-1700V 
Gate Resistor Range: 1-10Ω 
Input Signal: TTL/CMOS compatible

Safe line-monitored digital input module with earth fault monitor (16 channels) (conformal coated)

Control Module

Operating Voltage: 24V DC (±10%)
Power Consumption: 5–10W 
Isolation: 1500V AC
CPU: 32-bit RISC-based processor
Clock Speed: 100–200 MHz
Memory Flash:16–32 MB
Digital I/O: 24V DC

Circuit Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 15W (typical)
Operating Current: 0.5-1A
Isolation Voltage: 2000V AC 
Main Processor: 32-bit DSP or microcontroller
Clock Speed: 100-200MHz

Velomitor XA Piezo-Velocity Sensor

Sensitivity:3.94mV/mm/s (100 mV/in/s)±5%
VelocityRange:1270 mm/s (50 in/s) peak
Transverse Sensitivity:Less than 5% of sensitivity
Amplitude Linearity:±2% to 152 mm/s (6 in/s) peak
MountingTorque:45 N-m (33 ft-lb) maximum

Inverter Drive

IGCT MODULE

Voltage Rating:4500V (VCES)
Current Rating:4000A (IT(RMS))
Max. Turn-off Current:6000A (ITGQM)
On-State Voltage Drop:1.85V (typical @ 4kA)
Switching Frequency:Up to 500Hz 
Gate Driver Voltage:±20V (isolated)

Current Input Module

16, isolated
4 to 20 mA 
24 mA
270 Ω (20 mA) to 350 Ω (4 mA)
±16 µA 
230 mA (5 V DC), 540 mA (24 V DC)

Power supply module

Input Voltage Range:85-264V AC (47-63Hz) 
Output Voltage: 24V DC (±1% regulation)
Output Current: 10A 
Power Rating: 240W
Inrush Current: <30A (at 230V AC)
Overvoltage Protection: 28V DC 
Overcurrent Protection: 110-130% of rated current
Line Regulation: ±0.5% (85-264V AC)
Load Regulation: ±1% (20-100% load)

Modbus TCP/IP to EtherNet/IP Gateway

Backplanes

1 to 16 module slots
Seamless connection / possible
Stabile mechanics / compact design
Vibration proof fixing of modules
Can be snapped on EN 60715 DIN rail

Analog Input Module - HART

Digital Input Module

Driver board

Model Number: UF C911B108 3BHE037864R0108
Input Voltage: 24V DC 
Output Voltage: Adjustable based on application requirements
Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Humidity Range: 5% to 95% (non-condensing)

Communications I/O Module

Supply Voltage: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Primary Protocol: Profibus DP
Data Rate: 9.6kbps to 12Mbps
Connector Type: 9-pin D-sub
Isolation: 1500V AC
Digital Inputs: 8 channels

Communications I/O module

Supply Voltage:24V DC (±10%)
Power Consumption:4W (typical)
Inrush Current:<15A (20ms)
Backplane Current:500mA max
Output Isolation:3000V AC
Data Rates:9.6 kbps – 12 Mbps
Connector:9-pin D-sub (RS-485)
Address Range:0–126
Isolation:1500V AC

Exciter Control Module

Supply Voltage: 110/220V AC ±10%
Power Consumption: ≤15W
Generator current: 0-5A AC (CT input)
Field voltage: ±200V DC
Field current: ±5V DC
Response Time: <20ms for 95% step response

Proximitor/Seismic I/O Module

Radial Vibration
Thrust Position
Differential Expansion
Shaft Absolute
Eccentricity
Acceleration
Velocity

Universal Safety Interface (conformal coated)

Universal Safety Interface (conformal coated)

Control Board

Supply Voltage:24V DC (±10%)
Power Consumption:≤10W
Isolation:1500V AC
Processor:32-bit RISC microcontroller/DSP
Clock Speed:100-200 MHz
Analog Inputs:4-8 channels
Digital I/O:8-16 channels

Power Supply Module

Input Voltage:3-phase: 380-480V AC (±10%), 50/60Hz
Output Voltage:24V DC (±1%)
Output Current:20A (continuous)
Power Rating:480W
Efficiency:>92% (at full load)
Inrush Current:<40A (at 480V AC)

Control Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 8W (typical)
Processor: 32-bit DSP
Clock Speed: 150 MHz
ADC Channels: 16-bit, 12 channels
Analog Inputs:6 channels 
Isolation:2500V AC

Control Board

Processor: Dual-core 32-bit DSP 
Clock Speed: 300 MHz
Power Supply: 24V DC 
Power Consumption: 12W (typical)
Isolation:3000V AC
Control Loop Speed: 25μs (basic)
PWM Resolution: 16-bit @ 8kHz
Protection Response: <10μs 

Control Module

Supply Voltage:24V DC 
Processor:Triple-core 32-bit DSP
Clock Speed:400 MHz 
Memory:512KB SRAM
Power Consumption:18W (typical)
Analog Inputs:12× 18-bit ΣΔ ADC (±15V, 500kS/s)
Analog Outputs:6× 16-bit DAC (0-10V/4-20mA)
Digital I/O:24× configurable (5V TTL to 30V DC)

Control board

Supply Voltage: 24V DC
Power Consumption: 6W typical
Isolation:2500V AC
Processor: 32-bit RISC
Clock Speed: 216 MHz 
Memory SRAM: 256KB
Analog Inputs:6 channels
Digital I/O:12 opto-isolated inputs 

Accelerometers

02 ¼-28 to M8 x 1.25 Stainless Steel
00 No Approvals
Broadband ElectricalNoise:350 µg 
Output Bias Voltage: 8 to 12 VDC
Excitation Voltage:18 to 28 VDC
Constant CurrentExcitation: 2 to 20 mA 

Analog Input Baseplate

Fault current130 mA,
typical200 mA, maximum
Current Input: 4–20 mA, 0–20 mA.
Voltage Input: 0–10 V DC, ±10 V DC
Resolution:16-bit resolution
Accuracy:±0.1% of full scale
Channel-to-channel isolation: 1500 V AC/DC
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Storage Temperature:
-40°C to +85°C (-40°F to +185°F)

Analog Output Module

Output Type: Analog (Voltage or Current)
Output Range: 0-20 mA, 
Channels: 4 channels of output .
Resolution: Typically 16-bit .
Output Accuracy: ±0.1% of full scale
Power Supply: 24 V DC
Current Draw: 200-400 mA .
Operating Temperature: Typically from -20°C to +60°C 

ACCESSORY CONNECTOR SET SCREW C7 I/O PS

Current Input Module

Number of input channels 16 channels, module isolation
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C

Analog Output Module - HART

SIMATIC, electronic module 
for ET200iSP, 4 AO HART 4 - 20 mA
for connecting HART field devices
supported HART protocol version 6.0