ALL MANUFACTURERS

CPU412-2 Central Processor Module

VelocityTransducers

06 0 ±100, 10 Hz (600 cpm) 
01 Top Mount (no cable)
10 Circular; M10X1 stud
00 No Approvals
Sensitivity 20 mV/mm/s (500 mV/in/s)
Calibration Load 10 kΩ Terminal 
"A" to "B" Outputtaken across pins "A" and "B"
SensitivityTemperatureCoefficient0.2%/°C
CoilResistance 1.25 kΩ ±5%
Locked CoilInductance 125 mH, typical
Operatingand StorageTemperature:
-29°C to +121°C(-20°F to +250°F)

Digital Output Module

Relay Version: 5–250 VAC/VD
Solid-State Version: 24 VDC
Switching Frequency Relay: ≤5 Hz
Solid-State: ≤100 Hz
Channel-to-Channel: 500 VAC
Channel-to-Backplane: 1500 VAC

VerticalPlus I/O Carrier

Local Bus Power:12.6 VDC at 15 A 
AmbientTemperature:-40°C to +70°C
Shock :10g ½ Sinewave for 11msec
Vibration:1mm Peak to Peak from 2 to 13.2Hz;
0.7g from 13.2 to 150Hz
AirborneContaminantsISA-S71.04 –1985 
AirborneContaminants Class G3
Relative Humidity 5 to 95% Non-Condensing 

Main Control Circuit Board

PROFIBUS DP
PROFINET
Modbus RTU/TCP
Ethernet/IP
Clock Speed: ≥200 MHz 
Supply Voltage: 24 VDC (±10%)
Power Consumption: Typically <15W

CIRCUIT BOARD

Primary: 24VDC nominal
Backplane Outputs: +5V
Current Capacity:Up to 20A

Single Board Computer

Front Panel USB Ports
Front Access Reset Switch
15-Pin SVGA Port

I/O Pack Processor Board

Estimated 512 MB+ RAM
Modbus TCP/IP, Ethernet/IP
Analog (AI): ±10V DC, 4-20 mA
Digital (DI): 24V DC
Power Supply: 24V DC (±20%)
Power Consumption: < 10W

Dynamic Measurement Module

1444DYN0401RA
DYNAMIC MEASUREMENT MODULE
4 DYNAMIC INPUTS
2 TTL SPEED INPUTS
1 RELAY
2-PORT ETHERNET/IP (DLR)
SYNCHRONOUS OR ASYNCHRONOUSDYNAMIC 

Analog Input Module - 2 AI High Speed

Communication Module

PROFIBUS: 9.6 kbps to 12 Mbps
Modbus TCP: 10/100 Mbps
PROFIBUS: 9-pin D-sub
Ethernet: RJ45
Terminal blocks for serial communication
PROFIBUS: Up to 124 slaves
Modbus: 247 RTU devices 
Isolation: 1500 VAC 

PowerFlex 755 AC Packaged Drive

LOGO! DM8 12/24R Expansion Module

LOGO! DM16 24R Expansion Module

LOGO! 12/24RCE Logic Module

Eddy-Current Sensor series components

DIN-Rail mount
Configurable (USB)
Sensor type configurable
System cable length configurable
Measurement range configurable
Configurable sensor target material

Interface Board

Number of channels: 16 (configurable)
Voltage range: 24 VDC (18-30V)
Input impedance: 3kΩ
Isolation: 500V channel-to-channel
Switching capacity: 0.5A @ 24VDC
Supply Voltage: 24 VDC (±10%)
Power Consumption: <3W typical

Dual Modbus Plus port to dual Ethernet gateway

Robot Drive Unit

Input Voltage:3-phase 200-480VAC (±10%)
DC Bus Voltage: 600VDC nominal
Power Rating: 7.5kW (varies by configuration)
Peak Current: 25A (3 sec)
Continuous Current: 12A
PWM Frequency: 8kHz
Control Cycle Time: 0.5ms
Overload Capacity: 200% for 3 seconds

TRANSMITTER

TRANSMITTER
SEISMIC
01
0 25.4 MM/S
10 HZ TO 1 KHZ

PanelView Plus 7 Graphic Terminal

PCU 50 Panel Control Unit

2 Wide Carrier

CP 343-1 Ethernet Module

SM422 Digital Output Module

Control Board

Main Processor: 32-bit DSP + FPGA
Clock Speed: ≥300 MHz
Memory Flash: 128MB 
Control Cycle Time: <100μs
Digital Inputs: 8 channels (24VDC)
Digital Outputs: 4 channels (relay)
Analog Inputs: 2 channels (±10V/4-20mA)
Analog Outputs: 2 channels (0-10V/4-20mA)

DriveBus Interface Module

Data rate: 10 Mbps
Max. distance: 100m (fiber length)
ModuleBus connection to AC 800M
Supply voltage: 24 VDC (±10%)
Power consumption: <5 W
Isolation: 1500 VAC 
Supports up to 12 drives per module