ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
Input Voltage:24 V DC
Power Consumption:≤ 8 W
Torque Response: ≤ 2 ms
Accel/Decel Rates: Up to 3x faster vs
Overload Capability: 200%
Type:Dynamic Performance Module
Power Supply:24V DC (±10%)
Power Consumption:≤ 3 W
Input Channels:8x Isolated Voltage Inputs
Resolution:16-bit
Accuracy:±0.1% of FS (Full Scale) at 25°C
Input Impedance ≥1 MΩ
Sampling Rate:10 ms/channel
Channel-to-Channel: 300V AC
Overvoltage Protection:±30V continuous
Overload Protection:±30V (voltage)
Power Supply:24V DC
Power Consumption:≤ 1.5 W
Input Channels:4x Isolated Channels
Voltage: 0–10V, ±10V, 0–5V
Current: 0–20mA, 4–20mA
Resolution:12-bit
Sampling Rate:2 ms per channel
Voltage: ≥100 kΩ
Isolation:1500V AC
Type:8-Channel Isolated
Sink/Source: Auto-detecting
Voltage Range: 15–30V DC
Input Current 3–8 mA
Response Time:≤ 2 ms
Isolation:1500V AC
Power Supply:24V DC
Power Consumption:≤ 1.8 W
DRIVE BOARD
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-FK
Number of Channels: Typically 4 or 8
Switching Capacity: Up to 2A per channel
Supply Voltage: 24V DC
Isolation Voltage: 1500V AC
Response Time: <1ms
Input Voltage:24V DC nominal (15-30V range)
Input Current :3-5mA per point
Output Type:Relay (Form C) or Solid State
Output Rating:2A @ 30V DC
Isolation Voltage:1500V AC
Response Time:<1ms (input)
Contact Configuration:96-position (48x2 rows)
Contact Material:Gold-plated copper alloy
Current Rating:1A per contact (max)
Voltage Rating:60V DC max
Contact Resistance:<20mΩ (initial)
Insulation Resistance:>100MΩ @500V DC
Mating Cycles: >500 insertions
Supply Voltage:24V DC ±10%
Power Consumption:20W (typical)
Processor:32-bit DSP (200MHz)
Memory:16MB Flash, 8MB RAM
Isolation Voltage:1500V AC (I/O to logic)
Analog I/O update rate: 1 kHz
Digital I/O update rate: 10 ms
Standard range: -20°C to +60°C
Extended range: -40°C to +70°C
Power consumption: Max. 10W
Humidity: 5% to 95% RH
16-bit resolution for analog inputs/outputs
Input Voltage Range:5-30V DC (HTL)
Input Frequency:0-500kHz
Output Signal:Differential (RS422) or single-ended
Output Current:20mA max
Power Supply:24V DC ±10%
Power Consumption:5W typical
Resolution: Up to 4096 pulses/revolution
Signal Delay: <100ns
Operating Time:<8ms for critical faults
Measurement Accuracy:±0.5% of reading
Sampling Rate:64 samples/cycle
Time Sync Accuracy:±1μs
Power Supply:48-125V DC or 90-264V AC
Power Consumption:15W typical
Isolation Voltage:2.5kV AC
16 digital inputs (24V DC)
Configurable as sinking/sourcing
3ms debounce filtering
Channel-by-channel LED status
Voltage Range:5-30V DC
Current:3mA typical
Isolation:1500V AC
Analog Input :4-20mA/0-10V
Analog Output:4-20mA/0-10V
Digital Input:24V DC
Digital Output:24V DC, 0.5A
Resolution:16-bit
Accuracy:±0.1% of span
Input Impedance:250Ω
Input Voltage:24V DC (15-30V range)
Output Current:0.5A max per channel
Response Time:<1ms
Backplane Interface: Redundant S800 I/O bus
Update Rate: 10ms (all channels)
Rated Current (Ie):6A (AC-1)
Rated Voltage (Ue):230V AC / 24V DC
Breaking Capacity:3A @ 400V AC (AC-3)
Contact Material:Silver alloy (AgSnO₂)
Coil Voltage:24V DC / 48V DC / 110V AC / 230V AC (selectable)
Power Consumption:2.2W (DC) / 3.5VA (AC)
Operate Time:≤15ms (DC), ≤20ms (AC)
Release Time:≤10ms (DC), ≤15ms (AC)
