ABB

Extension Card I/O

Supply Voltage: Typically 24V DC
Voltage range: 24V DC
Load capacity: Up to 2A per channel 
Resolution: 12/16-bit
Signal types: 4–20mA, 0–10V

DIFFERENTIAL UNIT

Rated Current (In): Typically 1A or 5A
Frequency: 50/60 Hz
Harmonic Restraint: 2nd/5th harmonic blocking
Number of phases: 3 
Trip contacts: Normally 4–6 changeover
Rated load: 5A @ 250V AC/DC

IGBT MODULE

Emitter Voltage:1700V
Collector Current: 300A @ 80°C
Pulsed Current : Up to 600A
Switching Frequency: Up to 20kHz
Low Saturation Voltage:2.0V 
Isolation Voltage: 2500V AC (min)

DDCS Communication Option Module

Supply Voltage: 24V DC (±10%)
Power Consumption: <5W (typical)
Operating Current: 200mA @ 24V DC
Communication Speed: Up to 12Mbps
Optical: ST or BFOC type
Electrical: Terminal block or D-sub

CAPACITOR UNIT

Rated Voltage:400V AC
Rated Frequency: 50/60 Hz
Rated Reactive Power 25 kvar
Capacitance (C): ~500 µF 
Rated Current:36 A
Insulation Resistance: ≥ 3000 MΩ

Digital Input Module

Input Channels: 16 or 32 channels
Isolation: 500V
Input Voltage Range: 24V DC
Input Current: Typically 3-5mA 
On-State Voltage: 15-30V DC
Off-State Voltage: 0-5V DC
Response Time: <1ms (typical)
Input Impedance: ~3kΩ (typical)

Binary output module

24 binary outputs with enclosed relays (NO contacts)
Current carrying capacity of the relays: max. 1 A
Channel-by-channel isolation of the outputs
Module is capable of redundant operation
Monitoring of the module
Counter for switching cycles (channel by channel)

Combined overcurrentand earth-fault relay

Rated Current (I_n): 1 A or 5 A
Current Input: ≤ 0.1 VA
Frequency Range: 45–65 Hz
Binary Inputs: 5 (24–250 V DC/AC)
LED Indicators: 9 (Trip, Start, Alarm, Ready, etc.)
Operating Temperature: -25°C to +55°C
Storage Temperature: -40°C to +70°C
Humidity: ≤ 95% RH (non-condensing)

Drive control unit

Supply Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Isolation: 500V AC 
2x RJ45 Ethernet ports 
USB port for local configuration
8 digital inputs (24V DC)
4 digital outputs (24V DC, 0.5A)
2 analog inputs (±10V or 0/4-20mA)
2 analog outputs (0/4-20mA)

DDCS Branching Unit

Protocol: ABB DDCS 
Baud Rate: 12Mbps
Supply Voltage: 24V DC (±10%)
Power Consumption: 10W typical
Isolation: 500V AC
Fiber Type: Multi-mode 62.5/125μm

Submodule Carrier

Supply Voltage: 24V DC (±10%)
Power Consumption: 2W
Backplane Current: 1A maximum per slot
Isolation: 500V AC
System Connection: S800 bus to main controller
Field Connection: Screw terminals for I/O wiring
Bus Speed: 1.5Mbps 

PC I/O BOARD

Number of Channels: 16 or 32 
Input Voltage: 24V DC
Isolation: 500V opto-isolation
Channels: 8 single-ended 
Input Range: 0–10V, ±10V

Variable Frequency Drive

Power Range: 0.55kW
Low Voltage: 380-480V AC
Medium Voltage: 500-690V AC
Input Frequency: 47-63Hz
Output Frequency: 0-300Hz 
Overload Capacity: 110% continuous
Digital Outputs: 3 relay (2A/250V AC)
Analog Outputs: 2 (0/4-20mA or 0-10V)

Power Board

Input Voltage:24V DC nominal 
Output Voltage:+5V DC (±1%)
Current Capacity:10A (50W)
Total Power: 170W maximum
Efficiency: >85% at full load
Ripple Noise: <50mV p-p
Reverse polarity protection
Overvoltage protection (35V DC max)
Inrush current limiting

FEEDER TERMINAL

Rated Voltage (Vn): 100/110V AC
Burden: <0.2 VA per phase
Rated Current (In): 1A or 5A
Burden: <0.1 VA per phase at In
Digital Inputs: 8–16 
Contact Rating: 5A @ 250V AC/DC
Power Consumption: <15W (typical)

SWITCH-DISCONNECTOR

3-pole
front operated
base mounted
DIN-rail mountable switch-diconnector
non-fusible diconnect switch 
with front protected clamp terminals
handle and shaft are not included

PEC80 Converter Signal Int

Input Voltage Range: 24V DC
Operating Voltage: 15–30V DC 
Current Consumption: 50–200 mA 
Isolation Voltage: ≥500V 
Analog inputs: ±10V, 4–20mA
Digital inputs :TTL/relay contact

Controller I/O Module

Supply Voltage: 24V DC 
Power Consumption: 2–5W
Isolation: 500V AC 
Voltage: 24V DC
Switching Frequency: Up to 1 kHz
Range: 0–10V, ±10V, 4–20mA
Resolution: 16-bit (high precision)
Accuracy: ±0.1% FS (full scale)

Control Board

Supply Voltage: 24V DC
Isolation: 500V AC
CPU: 32-bit industrial 
Clock Speed: 100–200 MHz 
Memory Flash: 8–16 MB
Digital I/O:2–4 channels

Converter Electronics

CONVERTER
POWER CONTROL UNIT
UNS 3670A-Z V1
Input Voltage Range: 380-480V AC
DC Link Voltage: 510-650V DC
Output Power Rating: 15-30kW
Frequency Range: 50/60Hz ±10%
Efficiency: >95% 
Switching Frequency: 2-8kHz

Conduction Monitoring Coil

Rated Current: 50A to 5000A 
Frequency Range: 50/60Hz ±10%
Output Signal: 0-5V or 4-20mA
Accuracy Class: 1% or better 
Phase Shift: <3° at rated current

Three-phase voltage relay

Rated Voltage: 100-480V AC
Frequency Range: 45-65Hz
Input Impedance: >100kΩ per phase
Burden: <0.2VA per phase
Measuring Accuracy: ±1% of set value or ±0.5V 
Voltage Unbalance: 5-30% of Un
Contact Rating: 5A @ 250V AC/DC

Flame Controller

Flame Signal Input: 1 or 2 UV 
Sensitivity Range: Adjustable 0.1-100μA flame current
Power Supply:100-240V AC ±10%, 50/60Hz
Power Consumption: ≤5VA
Relay Outputs:2-4 SPDT (Form C) relays
Analog Output: 4-20mA flame strength signal 

Amplifier Board

Input Voltage Range: ±10V 
Output Voltage Range: ±10V 
Current Output: 0-20mA / 4-20mA
Gain Range: 1 to 1000 
Bandwidth: DC to 10kHz (-3dB)
Input Impedance: >1MΩ 
Output Impedance: <100Ω
Common Mode Rejection Ratio (CMRR): >80dB @ 60Hz
Noise Level: <10μV RMS (1Hz to 10kHz)

Universal Input Module

Number of Channels: 8 
Voltage: 0–10V
Current: 0–20mA, 4–20mA
Resolution: 16-bit 
Sampling Rate: 10 samples/sec per channel
Common-Mode Rejection (CMRR): >120 dB @ 50/60 Hz
Voltage Mode: >1 MΩ
Current Mode: 250 Ω