ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
Supply Voltage:24V DC (±10%)
Power Consumption:8W (max)
Encoder Inputs:2x (differential RS422)
Resolution:20-bit absolute
Update Rate:4kHz
Robot Bus:DSQC serial link
I/O Connection:16x digital I/O
Model Number: C41-91824
Type: Flow Control Valve
Pressure Class: ANSI 150/300
Flow Coefficient (Cv/Kv): Cv = 12.5
Extended: Up to +400°C
Control Signal: 4–20 mA, 0–10 V
Channels: 16 digital inputs
Rated Voltage: 24 V DC
Input Voltage Thresholds:15–35 V
Input Current: ~5 mA at rated voltage
Voltage Drop (at 500 mA): ≤0.5 V
Leakage Current: ≤0.1 mA
Response Delay: ≤0.5 ms
Power Dissipation (per channel): 150 mW
Digital Inputs:24V DC
Control Voltage (Logic Side): 24V DC
High Voltage (Power Side): 3.3 kV
Control Signals: ≤ 5A
Control-to-Power Isolation: ≥ 2500V AC
Main Processor: 32-bit RISC-based CPU
Clock Speed: 200–500 MHz
Operating Voltage: 24V DC (±10%)
Power Consumption: 5–15W
Isolation: 1500V AC
Ethernet/IP:10/100 Mbps
Digital Inputs: 24V DC
Digital Outputs: Channels 4–8
Current Inputs: 0–20 mA / 4–20 mA
Voltage Inputs: ±10 V DC, 1–5 V DC
Voltage Inputs: ±10 V DC, 1–5 V DC
Input Sharing: Supports HART communication
Accuracy: ±0.1% of span
Sampling Frequency: >300 scans/sec
Input Impedance: 250 Ω for current
Group isolation: 200 V RMS
Inter-track isolation: 250 V RMS continuous
Input Voltage: DC or AC
Output Current: Typically 10-100 A
Operating Temperature: -10°C to +60°C
Overload protection
Over-voltage protection
Under-voltage protection
Temperature protection
PC BOARD
INVERTER DRIVE BOARD
30 KW FOR ACS510 INVERTER
Input Voltage: 24V DC
Power Section Voltage: 380-690V AC
Signal Isolation:2500V AC
Analog inputs:0-10V/4-20mA
Digital I/O:24V DC
Control Voltage: 15 V DC
Protection Voltage: 12 V D
Operating Temperature Range: -20°C to +55°C.
Storage Temperature Range: -40°C to +70°C.
Humidity: 5% to 95% RH
CANopen
Modbus RTU
PROFIBUS DP
Input Voltage Range: 24 V DC
Operating Temperature: -25°C to +70°C
Storage Temperature: -40°C to +85°C
Humidity: 5% to 95% (non-condensing)
Supply Voltage:48 V dc
AC or DC Operation:DC
Power Consumption:40W
Air Flow:600m³/h
Noise Level:69dB
Fan Speed:7000rpm
Sensor Type:PWM, Tachometer
Bearing Type:Ball
Supply Voltage: 24V DC ±10%
Power Consumption: <15W typical
Voltage ranges: ±10V
Current ranges: 0-20mA
Resolution: 16-bit (minimum)
Sampling Rate: Up to 1kS/s per channel
Accuracy: ±0.1% of full scale
Isolation: 1500V AC
Input Voltage: Typically 24V DC
Operating Voltage Range: ±15V DC
Current Consumption:<500mA
Isolation Voltage: 1000V AC
Fiber optic or optocoupled signals
Digital I/O (for control signals)
Logic Side: 5V DC
Isolated Side: 15V DC
Current Rating: Typically <1A
Reinforced isolation:≥2500V AC
High-speed digital signals
Analog inputs:0-10V, 4-20mA
Input Voltage:230V AC
Range: Typically ±15%
Output Voltage:+24V DC
Auxiliary Outputs: ±15V DC
Efficiency: >85%
Isolation: 2500V AC
Terminal blocks for AC input and DC output
Multi-pin headers for control signals
Input Voltage:230V AC
Range: -15% to +10% of nominal
Frequency: 50/60Hz ±5%
Output Voltages:+24V DC (±1%)
Current Ratings:24V DC
Efficiency: >88% at full load
Ripple: <1% of nominal output voltage
Processor: 32-bit RISC processor
Memory:8MB RAM
Power Supply: 24V DC ±10%
Power Consumption: <15W
Operating Voltage Range: 18-30V DC
Screw terminals for power
BNC or ST-type fiber for Infi-net
DB9 or DB25 for serial
RJ45 for Ethernet (if equipped)
