ABB

DRIVE BOARD

Input Voltage:24V DC ±10%
Gate Drive Output:+15V/-8V (typical for IGBTs)
Isolation Voltage:2500V AC
Current Sensing Accuracy:±1% of full scale
Switching Frequency:Up to 20kHz
Fiber optic for control signals
Terminal blocks for power connections
Multi-pin headers for auxiliary signals

Extension Card I/O

Supply Voltage: Typically 24V DC
Voltage range: 24V DC
Load capacity: Up to 2A per channel 
Resolution: 12/16-bit
Signal types: 4–20mA, 0–10V

DIFFERENTIAL UNIT

Rated Current (In): Typically 1A or 5A
Frequency: 50/60 Hz
Harmonic Restraint: 2nd/5th harmonic blocking
Number of phases: 3 
Trip contacts: Normally 4–6 changeover
Rated load: 5A @ 250V AC/DC

IGBT MODULE

Emitter Voltage:1700V
Collector Current: 300A @ 80°C
Pulsed Current : Up to 600A
Switching Frequency: Up to 20kHz
Low Saturation Voltage:2.0V 
Isolation Voltage: 2500V AC (min)

DDCS Communication Option Module

Supply Voltage: 24V DC (±10%)
Power Consumption: <5W (typical)
Operating Current: 200mA @ 24V DC
Communication Speed: Up to 12Mbps
Optical: ST or BFOC type
Electrical: Terminal block or D-sub

CAPACITOR UNIT

Rated Voltage:400V AC
Rated Frequency: 50/60 Hz
Rated Reactive Power 25 kvar
Capacitance (C): ~500 µF 
Rated Current:36 A
Insulation Resistance: ≥ 3000 MΩ

Digital Input Module

Input Channels: 16 or 32 channels
Isolation: 500V
Input Voltage Range: 24V DC
Input Current: Typically 3-5mA 
On-State Voltage: 15-30V DC
Off-State Voltage: 0-5V DC
Response Time: <1ms (typical)
Input Impedance: ~3kΩ (typical)

Binary output module

24 binary outputs with enclosed relays (NO contacts)
Current carrying capacity of the relays: max. 1 A
Channel-by-channel isolation of the outputs
Module is capable of redundant operation
Monitoring of the module
Counter for switching cycles (channel by channel)

Combined overcurrentand earth-fault relay

Rated Current (I_n): 1 A or 5 A
Current Input: ≤ 0.1 VA
Frequency Range: 45–65 Hz
Binary Inputs: 5 (24–250 V DC/AC)
LED Indicators: 9 (Trip, Start, Alarm, Ready, etc.)
Operating Temperature: -25°C to +55°C
Storage Temperature: -40°C to +70°C
Humidity: ≤ 95% RH (non-condensing)

Drive control unit

Supply Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Isolation: 500V AC 
2x RJ45 Ethernet ports 
USB port for local configuration
8 digital inputs (24V DC)
4 digital outputs (24V DC, 0.5A)
2 analog inputs (±10V or 0/4-20mA)
2 analog outputs (0/4-20mA)

DDCS Branching Unit

Protocol: ABB DDCS 
Baud Rate: 12Mbps
Supply Voltage: 24V DC (±10%)
Power Consumption: 10W typical
Isolation: 500V AC
Fiber Type: Multi-mode 62.5/125μm

Submodule Carrier

Supply Voltage: 24V DC (±10%)
Power Consumption: 2W
Backplane Current: 1A maximum per slot
Isolation: 500V AC
System Connection: S800 bus to main controller
Field Connection: Screw terminals for I/O wiring
Bus Speed: 1.5Mbps 

PC I/O BOARD

Number of Channels: 16 or 32 
Input Voltage: 24V DC
Isolation: 500V opto-isolation
Channels: 8 single-ended 
Input Range: 0–10V, ±10V

Variable Frequency Drive

Power Range: 0.55kW
Low Voltage: 380-480V AC
Medium Voltage: 500-690V AC
Input Frequency: 47-63Hz
Output Frequency: 0-300Hz 
Overload Capacity: 110% continuous
Digital Outputs: 3 relay (2A/250V AC)
Analog Outputs: 2 (0/4-20mA or 0-10V)

Power Board

Input Voltage:24V DC nominal 
Output Voltage:+5V DC (±1%)
Current Capacity:10A (50W)
Total Power: 170W maximum
Efficiency: >85% at full load
Ripple Noise: <50mV p-p
Reverse polarity protection
Overvoltage protection (35V DC max)
Inrush current limiting

FEEDER TERMINAL

Rated Voltage (Vn): 100/110V AC
Burden: <0.2 VA per phase
Rated Current (In): 1A or 5A
Burden: <0.1 VA per phase at In
Digital Inputs: 8–16 
Contact Rating: 5A @ 250V AC/DC
Power Consumption: <15W (typical)

SWITCH-DISCONNECTOR

3-pole
front operated
base mounted
DIN-rail mountable switch-diconnector
non-fusible diconnect switch 
with front protected clamp terminals
handle and shaft are not included

PEC80 Converter Signal Int

Input Voltage Range: 24V DC
Operating Voltage: 15–30V DC 
Current Consumption: 50–200 mA 
Isolation Voltage: ≥500V 
Analog inputs: ±10V, 4–20mA
Digital inputs :TTL/relay contact

Controller I/O Module

Supply Voltage: 24V DC 
Power Consumption: 2–5W
Isolation: 500V AC 
Voltage: 24V DC
Switching Frequency: Up to 1 kHz
Range: 0–10V, ±10V, 4–20mA
Resolution: 16-bit (high precision)
Accuracy: ±0.1% FS (full scale)

Control Board

Supply Voltage: 24V DC
Isolation: 500V AC
CPU: 32-bit industrial 
Clock Speed: 100–200 MHz 
Memory Flash: 8–16 MB
Digital I/O:2–4 channels

Converter Electronics

CONVERTER
POWER CONTROL UNIT
UNS 3670A-Z V1
Input Voltage Range: 380-480V AC
DC Link Voltage: 510-650V DC
Output Power Rating: 15-30kW
Frequency Range: 50/60Hz ±10%
Efficiency: >95% 
Switching Frequency: 2-8kHz

Conduction Monitoring Coil

Rated Current: 50A to 5000A 
Frequency Range: 50/60Hz ±10%
Output Signal: 0-5V or 4-20mA
Accuracy Class: 1% or better 
Phase Shift: <3° at rated current

Three-phase voltage relay

Rated Voltage: 100-480V AC
Frequency Range: 45-65Hz
Input Impedance: >100kΩ per phase
Burden: <0.2VA per phase
Measuring Accuracy: ±1% of set value or ±0.5V 
Voltage Unbalance: 5-30% of Un
Contact Rating: 5A @ 250V AC/DC

Flame Controller

Flame Signal Input: 1 or 2 UV 
Sensitivity Range: Adjustable 0.1-100μA flame current
Power Supply:100-240V AC ±10%, 50/60Hz
Power Consumption: ≤5VA
Relay Outputs:2-4 SPDT (Form C) relays
Analog Output: 4-20mA flame strength signal 

Amplifier Board

Input Voltage Range: ±10V 
Output Voltage Range: ±10V 
Current Output: 0-20mA / 4-20mA
Gain Range: 1 to 1000 
Bandwidth: DC to 10kHz (-3dB)
Input Impedance: >1MΩ 
Output Impedance: <100Ω
Common Mode Rejection Ratio (CMRR): >80dB @ 60Hz
Noise Level: <10μV RMS (1Hz to 10kHz)

Universal Input Module

Number of Channels: 8 
Voltage: 0–10V
Current: 0–20mA, 4–20mA
Resolution: 16-bit 
Sampling Rate: 10 samples/sec per channel
Common-Mode Rejection (CMRR): >120 dB @ 50/60 Hz
Voltage Mode: >1 MΩ
Current Mode: 250 Ω 

Gate Driver Board

Input Voltage Range: 15-30V DC 
Output Drive Voltage: +15V/-8V
Peak Output Current: ±20A 
Isolation Voltage: 2500V AC 
Propagation Delay: <100ns
Compatible IGBTs: 1200V-1700V 
Gate Resistor Range: 1-10Ω 
Input Signal: TTL/CMOS compatible

Control Module

Operating Voltage: 24V DC (±10%)
Power Consumption: 5–10W 
Isolation: 1500V AC
CPU: 32-bit RISC-based processor
Clock Speed: 100–200 MHz
Memory Flash:16–32 MB
Digital I/O: 24V DC

Circuit Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 15W (typical)
Operating Current: 0.5-1A
Isolation Voltage: 2000V AC 
Main Processor: 32-bit DSP or microcontroller
Clock Speed: 100-200MHz

IGCT MODULE

Voltage Rating:4500V (VCES)
Current Rating:4000A (IT(RMS))
Max. Turn-off Current:6000A (ITGQM)
On-State Voltage Drop:1.85V (typical @ 4kA)
Switching Frequency:Up to 500Hz 
Gate Driver Voltage:±20V (isolated)

Power supply module

Input Voltage Range:85-264V AC (47-63Hz) 
Output Voltage: 24V DC (±1% regulation)
Output Current: 10A 
Power Rating: 240W
Inrush Current: <30A (at 230V AC)
Overvoltage Protection: 28V DC 
Overcurrent Protection: 110-130% of rated current
Line Regulation: ±0.5% (85-264V AC)
Load Regulation: ±1% (20-100% load)

Driver board

Model Number: UF C911B108 3BHE037864R0108
Input Voltage: 24V DC 
Output Voltage: Adjustable based on application requirements
Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Humidity Range: 5% to 95% (non-condensing)

Communications I/O Module

Supply Voltage: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Primary Protocol: Profibus DP
Data Rate: 9.6kbps to 12Mbps
Connector Type: 9-pin D-sub
Isolation: 1500V AC
Digital Inputs: 8 channels

Communications I/O module

Supply Voltage:24V DC (±10%)
Power Consumption:4W (typical)
Inrush Current:<15A (20ms)
Backplane Current:500mA max
Output Isolation:3000V AC
Data Rates:9.6 kbps – 12 Mbps
Connector:9-pin D-sub (RS-485)
Address Range:0–126
Isolation:1500V AC

Exciter Control Module

Supply Voltage: 110/220V AC ±10%
Power Consumption: ≤15W
Generator current: 0-5A AC (CT input)
Field voltage: ±200V DC
Field current: ±5V DC
Response Time: <20ms for 95% step response

Control Board

Supply Voltage:24V DC (±10%)
Power Consumption:≤10W
Isolation:1500V AC
Processor:32-bit RISC microcontroller/DSP
Clock Speed:100-200 MHz
Analog Inputs:4-8 channels
Digital I/O:8-16 channels

Power Supply Module

Input Voltage:3-phase: 380-480V AC (±10%), 50/60Hz
Output Voltage:24V DC (±1%)
Output Current:20A (continuous)
Power Rating:480W
Efficiency:>92% (at full load)
Inrush Current:<40A (at 480V AC)

Control Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 8W (typical)
Processor: 32-bit DSP
Clock Speed: 150 MHz
ADC Channels: 16-bit, 12 channels
Analog Inputs:6 channels 
Isolation:2500V AC

Control Board

Processor: Dual-core 32-bit DSP 
Clock Speed: 300 MHz
Power Supply: 24V DC 
Power Consumption: 12W (typical)
Isolation:3000V AC
Control Loop Speed: 25μs (basic)
PWM Resolution: 16-bit @ 8kHz
Protection Response: <10μs 

Control Module

Supply Voltage:24V DC 
Processor:Triple-core 32-bit DSP
Clock Speed:400 MHz 
Memory:512KB SRAM
Power Consumption:18W (typical)
Analog Inputs:12× 18-bit ΣΔ ADC (±15V, 500kS/s)
Analog Outputs:6× 16-bit DAC (0-10V/4-20mA)
Digital I/O:24× configurable (5V TTL to 30V DC)

Control board

Supply Voltage: 24V DC
Power Consumption: 6W typical
Isolation:2500V AC
Processor: 32-bit RISC
Clock Speed: 216 MHz 
Memory SRAM: 256KB
Analog Inputs:6 channels
Digital I/O:12 opto-isolated inputs 

INVERTER INTERFACE BOARD

Supply Voltage:24V DC (±10%)
Power Consumption:≤5W
Isolation Voltage:2500V AC (input-to-output)
Analog I/O:Range ±10V, 4-20mA
Digital I/O:24V DC 
Overvoltage:Auto-cutoff at 30V DC
Short Circuit:Current limiting
ESD Protection:±8kV (all ports)

Touch screen

2x Ethernet 10/100Mbit
1x RS-232/-422/-485
2x USB 2.0 Host
1x SD-card slot
2x Expansion slot
Storage capacity user data: 256 MB
Storage type user data: Flash Disk
Storage type user program: DDR RAM
Power consumption (@Pcons): 24 W
Power supply: 24 (18 ... 30) V DC
Screen colors: 64k colors

IMAGING CARD

Supply Voltage:24V DC (±5%)
Power Consumption:25W (typical)
Isolation :1500V AC 
Sensor Interface:GigE Vision (2 ports)
Camera Support:Up to 8MP resolution @ 60fps
Pixel Depth:8/10/12-bit
Throughput:2.5 TOPS (INT8)

Control Unit

Processor: Dual-core 32-bit RISC processor
Clock Speed: 800 MHz
Ethernet:4× 10/100/1000 Mbps (RJ45)
Serial:2× RS-485 (Modbus RTU)
IEC 61850:MMS, GOOSE, SV (Class 1)
Fieldbus:PROFIBUS DP-V1 (optional)
Power Supply: 48-250V DC or 100-240V AC
Power Consumption: 15W (typical)
Isolation: 4kV AC

Charging controllers

Input Voltage:380-480V AC, 3-phase (±10%)
Output Voltage:115 V AC or 230 V AC  ±10%, 50/60 Hz
Current Rating:20A (continuous), 30A (peak)
Efficiency:>94% (at full load)
Power Factor:>0.98 (at full load)
Overvoltage:+15% of setpoint
Overcurrent:110% for 60min
Reverse Polarity:Instant cutoff
Short Circuit:<1ms response

Servo Motor

Rated Power:4.5 kW
Rated Torque:28 Nm
Peak Torque:84 Nm (300% overload)
Rated Speed:1500 rpm
Max Speed:5000 rpm
Voltage:400V AC (3-phase)
Current:9.5A (rated), 28A (peak)
Torque Constant:1.8 Nm/A
Back EMF:110 V/krpm
Rotor Inertia:0.012 kg·m²
Stator Resistance:0.8 Ω (line-to-line)
Thermal Time Constant:45 minutes

REF542plus HMI Unit

Supply Voltage:24V DC (18-36V range)
Power Consumption:8W (typical)
Isolation :2kV AC 
Display Type:5.7" TFT LCD (color)
Resolution:320 × 240 pixels
Touch Panel:Resistive (single-touch)
Backlight:LED (50,000h lifespan)
Ethernet:10/100 Mbps (IEC 61850 MMS)
Optical Port: IR interface for local config
USB:Type B

Multi flame detector - control unit

Power Supply:120-220 Vac +/- 20%, 
45-65 Hz 24Vdc +/- 20%
AC input: 30 VA (6A / 5 ms inrush current)
DC input: 22 W (24A / 2 ms inrush current)
Operating: 0 - 60°C (32 - 140°F)
Storage: -25 - 85°C (-13 - 185°F)
Contact rating: 250 Vac 3 A 750 VA cosΦ 0.4
220 Vdc 300 mA 66 W

16 Bit Profibus DP Adapter Module

Up to 12 Mbps.
Auto-detection of baud rate
Address Range: Configurable from 0 to 126
Supply Voltage: 24 VDC ±10%.
Power Consumption: < 2 W
Operating Temperature: -10°C to +55°C.
Storage Temperature: -40°C to +70°C