Range Compatibility PacDrive 3
Maximum mechanical speed 4000 rpm
rated supply voltage 115...480 V
Phase Three phase
Continuous stall current 7.8 A
Continuous power 2900 W
Maximum current Irms 20.8 A
Range Compatibility PacDrive 3
Maximum mechanical speed 6000 rpm
rated supply voltage 115...480 V
Phase Three phase
Continuous stall current 3.5 A
Continuous power 1190 W
Maximum current Irms 12 A
Input Voltage: 24 V DC ±10% or 120-240 V AC
Power Consumption: Typically 20-30 watts
Operating Temperature Range: 0°C to 50°C (32°F to 122°F)
Storage Temperature: -20°C to 70°C (-4°F to 158°F)
Output: Analog (typically 4-20 mA)
M-Bus slave interface According to
EN 1434-3 and EN 13757-2/-3
Quiescent current ≤ 1.5 mA
Standard load 1UL
Addressing Primary or secondary
Baud rate 300, 2400 Baud
Polarity AnyDC decoupling Through module interface
Length of connection cable 2.95 m
Range compatibility PacDrive 3
Product or componenttypeServo motor
Device short name SH3.....P
Maximum mechanical speed 8000 rpm
rated supply voltage 115...480 V
Network number of phases Three phase
Continuous stall current 1.8 A
Continuous power 690 W
Maximum current Irms 5.7 A
Shaft end Smooth shaft
Power Supply:48V DC
Optical Interfaces:May support SFP
Ethernet: IEEE 802.3
Operating Temperature:-5°C to +55°C
Storage Temperature:-40°C to +70°C
Humidity:5% to 95% non-condensing
Voltage: Typically available in 230V or 400V
Frequency: 50/60 Hz
Motor Power: 0.2 kW
Protection Rating: IP54 or higher
Operating Temperature: -10°C to +40°C
Loop-powered
4-20 mA output proportional to acceleration
(ST6911) orvelocity (ST6917)
Loop terminals with Independent Polarity
(IPT®)to prevent incorrect wiring
Interfaces directly with PLC, DCS, 4-20 mA monitors, etc
M6 x 1 or 1/4 - 28” mounting studs
MIL style connector standard
Widest operating temperature in its class
Most stable detection circuit available
Temperature shock protected
“Ski slope” problem protected for high accuracy at lowfrequencies
Hermetically sealed
Bus expansion slave module
with 2 interfaces
Bus expansion slave module optionally
with integrated power supply
Up to 6 local substations
Minimal signal delay
Distances of up to 3 m between 2 stations
Integrated watchdog on slave modules
COMPRESSOR CONTROLLER
MK5 STD
Power Supply: 24 VDC
Operating Temperature: -10°C to +50°C.
Humidity: Up to 95% non-condensing.
Power Consumption: Low-power operation
Product:X-Gateways
Data Rate:100 Mb/s
Number of Ports:2 x RJ45
Interface Type:Ethernet, USB
Supply Voltage - Min:24 V
Supply Voltage - Max:24 V
Minimum Operating Temperature:- 25 C
Maximum Operating Temperature: + 65 C
Brand:HMS Networks
Dimensions:114 mm x 44 mm x 127 mm
IP Rating:IP20
Operating Supply Current:200 mA
Product Type:Gateways
Product:X-Gateways
Data Rate:12 Mb/s
Interface Type:Ethernet, USB
Supply Voltage - Min:24 V
Supply Voltage - Max:24 V
Minimum Operating Temperature: - 25 C
Maximum Operating Temperature: + 65 C
Brand:HMS Networks
IP Rating:IP20
Operating Supply Current:200 mA
Interface Type:USB
Minimum Operating Temperature: - 25 C
Maximum Operating Temperature: + 55 C
Brand:HMS Networks
Operating Supply Current:150 mA
Operating Supply Voltage:24 V
Type: EHPM02
Series: Experion PKS system
Voltage Requirements:24 V DC
Operating Temperature: -40°C to 70°C
Storage Temperature: -40°C to 85°C
Relative Humidity: 5% to 95% (non-condensing)
MULTI-AXIS CONTROLLER
FOR SERVO AND STEPPER MOTORS
3 SERVO AXES / 4 STEPPER AXES
DIFFERENTIAL STEPPER OUTPUT TYPE
2 EXTRA ENCODER INPUTS
RS232
SAME FIT/FORM/FUNCTION AS NSB202-501
Voltage: ±10 V, 0–10 V, or 4–20 mA signals.
Voltage: 0–10 V or ±10 V.
Current: 4–20 mA, configurable
Power Supply: +24 VDC
Operating Temperature: 0°C to 50°C .
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 95% (non-condensing).
Number of Channels: Typically 8 to 16 input channels
Voltage: ±10 V, 0–10 V, or 4–20 mA signals.
Resolution: 12-bit or higher
Accuracy: ±0.1% of full scale or better
Voltage: 0–10 V or ±10 V
Current: 4–20 mA, configurable
Resolution: 12-bit or higher
Power Supply: +24 VDC
Input Voltage: +5V, +12V
Current Consumption: Typically under 2A
RS-232/RS-485
Operating Temperature: 0°C to 50°C.
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 85% (non-condensing)
Loop-powered driver/transmitter
Compatible with 4 major probe systems
Easily factory calibrated to non-standard shaft material
DIN Rail mounting (flat mounting base available) (P/N 9647)
BNC for access to dynamic output and probe gap
PBT plastic material
Type: Digital Control Module
Voltage Input:
Typically operates on 24V DC
Operating Temperature Range: -40°C to +70°C
Storage Temperature Range: -40°C to +85°C
Analog voltage input ±10 V to ±10 mV
Analog current input 0(4) to 20 mA
Temperature sensor Pt elements as 2-,3-,4-wire
Thermo couples type J, K, T, N, E, R, S, B
Analog voltage output ±10 V
Analog current output 0(4) to 20mA
Resolution: 16-bit input with filter, 14-bit output
Galvanic isolation from the system 500 V
Power Supply:
Typically 12V DC or 24V DC
Operating Temperature Range:
0°C to 50°C (32°F to 122°F)
Humidity: Typically rated for
5% to 95% relative humidity
Series: Foxboro I/A Series
Power Supply: Typically 24V DC
Operating Temperature: 0°C and 60°C
Storage Temperature: -20°C and 70°C
Humidity: 5% and 95% (non-condensing)
Input Voltage: 200V-240V AC
Input Frequency: Typically 50/60 Hz
Output Frequency: 0 to 400 Hz
Storage Temperature: -20°C to 60°C
Operating Temperature: Typically between -10°C to 50°C
Humidity: 5% to 95% non-condensing
Highly Intuitive Design Environment
Graphical Configuration
Live Updating Loop Drawings
One-Spot Engineering Environment
Common Database Integrating System,
Control, Display and Field Device
Configuration in One Tool
Power Supply: Typically 24V DC
Operating Temperature: Usually from 0°C to 55°
Current Consumption: Typically around 100 mA
Input Voltage: 24V DC
Input Type: Dry contact
Number of Inputs: Typically up to 16 or 32 input points
Output Voltage: 24V DC
AC Input Voltage Range: 90-132V or 180-264V
Nominal Output DC Voltage: 24 VDC
Operating Temperature:
Typically 0°C to 50°C (32°F to 122°F)
Typically -20°C to 70°C (-4°F to 158°F)
Gateways Modbus
TCP/IP Master to
Modbus RTU Slave
Data Rate:115.2 kb/s
Number of Ports:2 x RJ45
Interface Type:Ethernet
Supply Voltage - Min:24 V
Supply Voltage - Max:24 V
Packaging:Each
Brand:HMS Networks
Dimensions:114 mm x 44 mm x 127 mm
IP Rating:IP20
Operating Supply Current:200 mA
Product Type:Gateways
SIMOTICS S Synchronous servo motor
1FK7 Compact 0.85Nm
100K, 6000rpm 0.38kW
Naturally cooled Power/signal connectors
Connector can be rotated
by 270° FRAME SIZE IMB 5 (IM V1, IM V3)
FLANGE 1 Absolute encoder
20BIT +12-bit multi-turn with
Drive-CLiQ interface (encoder AM20DQ)
Derating 10% due to absolute encoder
PLAIN SHAFT, TOLERANCE N
WITH HOLDING BRAKE
DEGREE OF PROTECTION IP64
SIMOTICS S synchronous servo motor
1FK7 Compact 1.1 Nm 100K,
6000 rpm 0.50 kW,
naturally cooled IM B5 (IM V1, IM V3)
power/signal connector plug rotatable by 270°
Absolute encoder 20BIT +12-bit
multi-turn with Drive-CLiQ interface (encoder AM20DQ)
Derating 10% due to absolute encoder plain shaft,
tolerance N with holding brake degree of protection IP64
SIMOTICS S SIMOTICS S-1FK7
1FK7-CT synchronous motor
PN=0.82 kW UDC=600 V
M0=3 Nm (100K); NN=3000
r/min; naturally cooled design MB 5 (IM V1, IM V3)
flange 1 power connector rotatable
absolute encoder 24 bit +12 bit
multiturn with DRIVE-CLiQ
interface (encoder AM24DQI) plain shaft,
tolerance N with holding
brake degree of protection IP64
SIMOTICS S SIMOTICS S-1FK7
1FK7-CT synchronous motor
PN=0.82 kW UDC=600 V
M0=3 Nm (100K); NN=3000
r/min; naturally cooled design MB 5 (IM V1, IM V3)
flange 1 power connector rotatable
absolute encoder 24 bit +12 bit
multiturn with DRIVE-CLiQ
interface (encoder AM24DQI) plain shaft,
tolerance N with holding
brake degree of protection IP64
Input Channels 32
Galvanic Isolation 1500 VAC RMS or ±1500 VDC
Isolation Technique Optical (in IOM)
DI Power Voltage Range 18 to 30 VDC
ON Sense Voltage/Current 13 VDC (min) or 3 mA (min)
OFF Sense Voltage/Current 5 VDC (max) or 1.2 mA (max)
Input Impedance 4.2
Absolute Delay Across Input Filter and Isolation 5 ms ± 20%
Field Resistance for Guaranteed ON Condition 300 max @ 15 VDC
Output Type 4-20 mA
Output Channels 16
Output Ripple < 100 mV peak-to-peak at
power line frequency, across 250 load
Output Temperature Drift 0.005% of Full Scale/°C
Output Readback Accuracy ±4% of Full Scale
Output Current Linearity ± 0.05% of Full Scale nominal
Resolution ± 0.05% of Full Scale
Calibrated Accuracy ± 0.35% of Full Scale (25oC) including linearity
Directly Settable Output Current Range 0 mA, 2.9 mA to 21.1 mA
Maximum Output Compliant Voltage 16 V
Common Mode Rejection Ratio, dc to 60 Hz 70 dB
Common Mode Voltage, dc to 60 Hz -6 to +5 V peak
A/D Converter Resolution 16 bits
Normal Mode Rejection Ratio, at 60 Hz 19 dB
Normal Mode Filter Response Single-pole RC, -3 dB @ 6.5 Hz
Maximum Normal Mode Input ± 30 Volts
Crosstalk, dc to 60 Hz -60 dB
Input Impedance (voltage inputs) > 10 M Ω powered
Input Scan Rate 50 ms
Input Type: Voltage current
(2-wire or self-powered transmitters)
Input Channels : 16 Channels
Common Mode Voltage, dc to 60 Hz -6 to +5 V peak
A/D Converter Resolution 16 bits
Normal Mode Rejection Ratio, at 60 Hz 19 dB.
Normal Mode Filter Response Single-pole RC, -3 dB @ 6.5 Hz
Maximum Normal Mode Inpu ± 30 Volts
Crosstalk, dc to 60 Hz -60 dB
Input Impedance (voltage inputs) > 10 M Ω powered
Input Scan Rate 50 ms
Power Supply Voltage:24 VDC
Operating Temperature Range:-20°C to +60°C
Communication Interface:RS-485
Input Current:Up to 10 mA
Output Power:150 mA
Humidity Range:
10% to 90% RH (non-condensing)
Power Supply Voltage:24 VDC
Operating Temperature Range:-20°C to +60°C
Communication Interface:RS-485
Input Current:Up to 10 mA
Output Power:150 mA
Humidity Range:
10% to 90% RH (non-condensing)
Power Supply Voltage:24 VDC
Operating Temperature Range:-20°C to +60°C
Communication Interface:RS-485
Input Current:Up to 10 mA
Output Power:150 mA
Humidity Range:
10% to 90% RH (non-condensing)
Power Supply Voltage:24 VDC
Operating Temperature Range:-20°C to +60°C
Communication Interface:RS-485
Input Current:Up to 10 mA
Output Power:150 mA
Humidity Range:
10% to 90% RH (non-condensing)
DC link voltage 510 ... 720 V DC
Electronics power supply 24 V DC -15%/+20%
1 electronics power supply connection
via integrated24 V DC busbars
3 DRIVE-CLiQ sockets
1 safe standstill input (enable pulses)
1 safe motor brake control
1 temperature sensor input
Type: Incremental encoder
Resolution: 360 pulses per revolution
Output: Likely TTL or HTL,
but could be other types like RS422
Supply Voltage: Typically 5V or 24V
Operating Temperature: -20°C to +85°C
Mounting: Shaft or flange mount
Housing: Plastic or metal
Shaft Diameter: Varies depending on the application
MPC60x Class of Microprocessors
16KB/16KB or 32KB/32KB L1 cache
256KB L2 cache
Up to 512MB ECC DRAM On-Board Memory
8MB on-board Flash, 1MB Socketed
Ethernet Transceiver Interface
with 32-Bit PCI Local Bus DMA
8- or 16-bit Fast SCSI-2 Bus Interface
Parallel, Floppy, Keyboard
and Mouse Interfaces
Motherboard (MB)
for IGS Gas Box systems.
Input Voltage: 24V DC
Operating Temperature: 0°C to 60°C (32°F to 140°F)
Storage Temperature: -20°C to 85°C (-4°F to 185°F)
Humidity: Up to 95% RH, non-condensing
Series: VIOP Phase III
Supported Signal Types: 4–20 mA, 0–10 V
Input Voltage: 5V DC or 24V DC
Output Types: 0–10 V, 4–20 mA
Operating Temperature: 0°C to 60°C (32°F to 140°F)
Storage Temperature: -20°C to 85°C (-4°F to 185°F)
Humidity Tolerance: 5% to 95% RH, non-condensing
PCBA VIOP Board
Series: VIOP Phase III Series
Voltage Range: 5V DC or 24V DC
Signal Types: 4–20 mA, 0–10 V
Input range: 0–24V DC
Operating Temperature: 0°C to +60°C (32°F to 140°F)
Storage Temperature: -20°C to +85°C (-4°F to 185°F)
Humidity: 5% to 95% non-condensing
PCBA VIOP Board
Series: VIOP Phase III Series
Voltage Range: 5V DC or 24V DC
Signal Types: 4–20 mA, 0–10 V
Input range: 0–24V DC
Operating Temperature: 0°C to +60°C (32°F to 140°F)
Storage Temperature: -20°C to +85°C (-4°F to 185°F)
Humidity: 5% to 95% non-condensing
PCB ASSY VIOP III
BOARD MODULE CARD
Name: VIOP Phase III Board
Operating Voltage: Typically 5V DC or 24V DC
Accepts signals such as 4–20mA
Current loops or 0–10V DC voltage inputs
Input range: 0–24V DC
Operating Temperature: 0°C to +60°C (32°F to 140°F).
Storage Temperature: -20°C to +85°C (-4°F to 185°F).
Humidity: 5% to 95% non-condensing.
LAM RESEARCH VIOP PHASE
Operating Voltage:
Typically 24V DC or 5V DC
Typical range: 0–10V DC, ±10V DC,
or 4–20mA current loop
Input voltage levels: Typically 0–24V DC
Operating Temperature:
Typically 0°C to +60°C (32°F to 140°F).
Storage Temperature:
-20°C to +85°C (-4°F to 185°F).
Humidity: 5%–95% non-condensing
Inputs :8
Input Type :Single-ended Non-isolated
Resolution :16 bits
Data Format :Configurable
Functional Data Range:15V at 22mA
Module Field-side Power Consumption:7.5 W
Power Dissipation:5.2 W
Thermal Dissipation:17.75 BTU/hour
Step Response:4 ms
4 safety inputs for 4 to 20 mA signals
forming 2 logic safety channels
Optional encoder supply via the module
4 safety inputs for temperature measurement (Pt100)
forming 2 logic safety channels
2 safety inputs for strain gauge signals
forming one logic safety channel
System Security via Password
Color Touch Screen with Full Screen Color Graphics
4 LEDs: Power / Network / COM 2 / COM 1
Modbus Master/Slave Configurations
Key Process Variable Display Capability
3 Display Operational Modes:
Local, Switchable or System
Rated Power: Typically 0.5 to 1.0 kW
Rated Voltage: AC 200-240V
Rated Speed: 3000 RPM
Shaft Diameter: Generally around 14 mm
Mounting Type: flange-mount
Operating Temperature Range: Typically -10°C to 40°C
Storage Temperature Range: Often between -20°C to 60°C
Channels 10-12 can be
used as an analog input of ±10 V
Analog inputs individually
configurable for sensitivity
24 bit A-D resolution with a
dynamic range ≥ 96 dB
Adjustable sampling
rate up to 51.2 kHz
Adjustable analog and digital filtering
Part Status Active
Function Gateway
Modulation or Protocol EtherNet/IP™
Applications General Purpose
Interface RJ-45 Ethernet
Data Rate (Max) 1Mbps
Operating Temperature °C Min -25 °C
Operating Temperature °C Max 65 °C
Storage Temperature °C Min -40 °C
Storage Temperature °C Max 85 °C
KUEP Series
Contact Current Class = 5A to 10A Class, LessThan 16A
Contact Rated Current = 10 A
Terminal Type = Quick Connect, Solder
Contact Arrangement = 1 Form X (NO,Bridging)
Rated current AC-1: 16 A
Rated current DC-1: 10 A
Rated current DC-13: 2 A
Rated voltage AC: 400 V
Rated voltage DC: 220 V
Minimum current: 10 mA
Minimum voltage: 10 V
Versorgungsspannung: AC
Nominal supply voltage min.: 115 V
Nominal supply voltage max.: 115 V
