ALL MANUFACTURERS

Interconnect Cable

3-Wire Cable
Interconnect Cable without Armor
33 = 33 ft / 10 metres

Digital I/O Card

Series Mark V
Part Number DS200TCDAG1B
Functional Description Digital I/O Board
Functional Acronym TCDA
PCB Coating Normal Coating

Controller Circuit Board

Input Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Isolation: 4kV AC
Processor: 32-bit PowerPC @ 400MHz
Memory:64MB SDRAM

Control I/O Module

Digital Inputs:24V DC
Analog Inputs:0-10V/4-20mA
Input Isolation:2.5kV AC
Backplane Bus:Proprietary high-speed bus
Protocol Support:Modbus RTU, PROFIBUS DP 

Control Circuit Board

Power Supply:24V DC (±10%)
Power Consumption:8W (typical)
Processor:32-bit ARM Cortex-M7 @ 400MHz
Memory:64MB Flash, 32MB RAM
Cycle Time:≤100μs
Digital I/O:24V DC
Analog Inputs:0-10V/4-20mA

FTA interconnection cable

Direct connection between two 
FS-CP series process controllers
10 meters long
Shielded twisted pair design
Easy to install and use
Hot-pluggable

CM30 Controller

Output Type:Analogue Relay
Supply Voltage:100 → 240 V ac
Number of Outputs:3
Control Type:ON/OFF
Communication Module Available:Yes
Display Type:LCD, Multi Line, TFT
IP Rating:IP66
Range:ControlMaster CM30
Additional Functionality:ON/OFF
Series:CM30
Panel Depth:121mm
Display Colour:Green, Red, Yellow

Servo Drive

Voltage: 3-phase 200-480V AC (±10%)
Frequency: 50/60Hz (±5%)
Power Range: 2.3kW to 7.5kW
Output Current: 6A to 18A RMS
Control Method: Field-Oriented Control 
Control Bandwidth: 1.5kHz
Speed Range: 0-6000 RPM
Positioning Accuracy: ±1 encoder count

AXIS Drive Unit

Input Voltage:3-phase 200-480V AC (±10%)
Frequency:50/60Hz (±5%)
Power Range:3.0kW 
Peak Current :18A 
Output Current:6A RMS
Switching Frequency:8kHz (PWM)

IGBT MODULE

Collector-Emitter Voltage: 1200 V or 1700 V
Gate-Emitter Voltage:±20 V (max)
Continuous Collector Current: 25–50 A
Peak Collector Current: 75–100 A
Turn-On Time：50–100 ns
Turn-Off Time：150–300 ns
Operating Temperature: -40°C to +125°C 
Storage Temperature: -40°C to +150°C

IGBT module

Collector-Emitter Voltage (Vces): 1700V
Gate-Emitter Voltage (Vges): ±20V
Turn-on Time (ton): 0.5μs (typical)
Turn-off Time (toff): 1.2μs (typical)
Switching Frequency: Up to 20kHz 
Power Dissipation: 1800W (max)
DC Link Voltage: 1000-1200V DC
Typical Applications:400-690V AC drives

Controller

Controller 
(20 digital inputs, 8 digital outputs)
Operating temperature: 0...+60 °C
for ELOP II Factory programming tool 

Ex2100 Excitation Control Interface Panel

OPERATOR INTERFACE
EX2100 EXCITATION CONTROL PANEL
12 BUTTON KEYPAD
16 CHARACTER ALPHANUMERIC DISPLAY
FIELD-REPLACEABLE

3300 XL 8 mm Probe

3300 XL 8 mm Probe
3/8-24 UNFthread, without armor
90 9.0 meters (29.5 feet)
02 Miniature coaxial ClickLocconnector
standard cable
05 CSA, ATEX, IECEx  Approvals

3300 XL 8 mm Proximity Probes

330101  3300 XL 8 mm Probe
3/8-24 UNFthread, without armor
Minimum unthreaded length: 0.0 in
Minimum case length: 4.9 in
10 1.0 meter (3.3 feet)
02 Miniature coaxial ClickLocconnector
standard cable
05 CSA, ATEX, IECEx  Approvals

3300 XL 8 mm Proximity Probes

330101  3300 XL 8 mm Probe
3/8-24 UNFthread, without armor
Minimum unthreaded length: 0.0 in
Minimum case length: 4.9 in
90 9.0 meters (29.5 feet)
02 Miniature coaxial ClickLocconnector
standard cable
05 CSA, ATEX, IECEx  Approvals

CPU1215C Compact Unit

Controller with Expanded Memory

Processor:32-bit ARM
Base Memory:512MB DDR4 RAM
Expanded Memory:2GB Flash
Execution Speed:0.05ms/1k instructions
I/O Scan Time:≤1ms (for 1000 I/O points)
Task Capacity:32 concurrent tasks
Digital I/O:Up to 2048 points
Analog I/O:Up to 512 channels
Input Voltage:24V DC (±15%) or 100-240V AC
Power Consumption:15W (typical)

Active Line Module

Scanner head

Scanner head,
IR sensor.
3/4in threade
Power Supply: 24V DC (±10%)
Power Consumption: 50W (typical)
Wavelength Range: 900-1100nm
Spot Diameter: 0.2-3.0mm (adjustable)
Focal Length: 150-450mm (motorized adjustment)
Scanning Angle: ±30° (optical)
Positioning Accuracy: ±0.01°

COMMUNICATION BOARD

PROFIBUS DP:9-pin D-sub, 12Mbps max
Modbus RTU:RS485 (terminal block)
Power Supply:24V DC (±10%), sourced from drive
Power Consumption:3W (typical)
Isolation :1.5kV AC (fieldbus to drive)
Signal Levels :RS485: ±15V differential

DIRECT CURRENT FEEDBACK BOARD

DIRECT CURRENT FEEDBACK BOARD
EX2100 SERIES
Board Description:Exciter DC Feedback
Board Type:Input/Output Terminal Board
External Power Supply:±24 VDC
Functional Acronym/Abbreviation:EDCF
Hardware Form:A, Not Backward Compatible

Exciter Gate Pulse Amplifier Board

Series: EX2100
Product Type: Exciter Gate Pulse Amplifier Board
Operating System: QNX
Power Requirements: +5 V dc, 6 A
Number of input channels: 24
Trip Solenoid Rating: 125 V dc
Power supply voltage: 28 V dc