PC BOARD
INVERTER DRIVE BOARD
30 KW FOR ACS510 INVERTER
Input Voltage: 24V DC
Power Section Voltage: 380-690V AC
Signal Isolation:2500V AC
Analog inputs:0-10V/4-20mA
Digital I/O:24V DC
Control Voltage: 15 V DC
Protection Voltage: 12 V D
Operating Temperature Range: -20°C to +55°C.
Storage Temperature Range: -40°C to +70°C.
Humidity: 5% to 95% RH
CANopen
Modbus RTU
PROFIBUS DP
Input Voltage Range: 24 V DC
Operating Temperature: -25°C to +70°C
Storage Temperature: -40°C to +85°C
Humidity: 5% to 95% (non-condensing)
Supply Voltage:48 V dc
AC or DC Operation:DC
Power Consumption:40W
Air Flow:600m³/h
Noise Level:69dB
Fan Speed:7000rpm
Sensor Type:PWM, Tachometer
Bearing Type:Ball
Supply Voltage: 24V DC ±10%
Power Consumption: <15W typical
Voltage ranges: ±10V
Current ranges: 0-20mA
Resolution: 16-bit (minimum)
Sampling Rate: Up to 1kS/s per channel
Accuracy: ±0.1% of full scale
Isolation: 1500V AC
Input Voltage: Typically 24V DC
Operating Voltage Range: ±15V DC
Current Consumption:<500mA
Isolation Voltage: 1000V AC
Fiber optic or optocoupled signals
Digital I/O (for control signals)
Logic Side: 5V DC
Isolated Side: 15V DC
Current Rating: Typically <1A
Reinforced isolation:≥2500V AC
High-speed digital signals
Analog inputs:0-10V, 4-20mA
Input Voltage:230V AC
Range: Typically ±15%
Output Voltage:+24V DC
Auxiliary Outputs: ±15V DC
Efficiency: >85%
Isolation: 2500V AC
Terminal blocks for AC input and DC output
Multi-pin headers for control signals
Input Voltage:230V AC
Range: -15% to +10% of nominal
Frequency: 50/60Hz ±5%
Output Voltages:+24V DC (±1%)
Current Ratings:24V DC
Efficiency: >88% at full load
Ripple: <1% of nominal output voltage
Processor: 32-bit RISC processor
Memory:8MB RAM
Power Supply: 24V DC ±10%
Power Consumption: <15W
Operating Voltage Range: 18-30V DC
Screw terminals for power
BNC or ST-type fiber for Infi-net
DB9 or DB25 for serial
RJ45 for Ethernet (if equipped)
Number of Channels: 16 connection points
Isolation: 250V AC
Rated Voltage: 250V AC/DC
Current Rating: 2A per channel
Contact Resistance: <50mΩ
Insulation Resistance: >100MΩ @ 500V DC
Dielectric Strength: 2000V AC (50Hz)
Frequency range: 1Hz-20kHz
Input sensitivity: 50mV RMS minimum
Isolation: 1500V AC between channels
Analog Inputs:4-20mA position
Control Outputs: 4-20mA governor control signal
Power Supply:24VDC nominal
Accuracy: ±0.1% of reading ±1 RPM
DC Bus Monitoring:0–1000V DC typical
Logic Side: +24V DC (±10%)
Gate Drive Side: +15V/-8V
Current Consumption:<500mA
Gate Drive: Peak 2A
Reinforced Isolation: 2500V AC
Working Voltage: 1000V DC
24 V supply current: max. 25 mA
5 V supply voltage: 5 Vdc ± 5%
5 V supply current: max 1.2 A
Output supply voltage: 15—31 Vdc
Output resistance: approx. 1.1 kΩ
Short circuit proof: continuous
Voltage (high): 15—32 Vdc
Voltage (low): <4 V (reverse polarity protected)
Input current: approx. 8mA at 24 Vdc
Output current: 750mA per output
Input Current Range:±10A (direct input)
Output Signal:4-20mA analog output
Analog Output: 4-20mA (load ≤500Ω)
Accuracy: ±0.5% of full scale
Bandwidth: 10kHz (-3dB point)
Isolation Voltage: 2500V AC
Input Voltage: 24V DC
Power Consumption: ≤1.5W
Isolation: 500V AC
Signal Conditioning:16-bit ADC resolution
Analog Input:4-20mA + HART
4-20mA loop drive: ≤500Ω
Communication Speed: 1200 bps (FSK)
Multidrop Mode: Supports up to 15 devices
Power Supply Unit 24/5 Vdc, 16A (conformal coated)
Operating temperature:-5°C-+70°C (+23°F-+158°F)
Storage temperature: -40°C-+85°C (-40°F-+185°F)
Relative humidity: 10-95% (non condensing)
Approvals:CE, TUV, UL, CSA, FM
24 V supply voltage: 24 V DC -15%-+30%
24 V supply current:
< 6 A at 24 Vin (16 A load)
< 7 A at 20.4 Vin (16 A load)
Inrush current: < 5 A at 24 Vin
Hold-up time: < 1ms
Magnetic pickup (MPU) or proximity probe
Frequency range: 1Hz to 10kHz
Input sensitivity: 50mV RMS minimum
Accuracy: ±0.1% of reading ±1 RPM
Analog Output:4-20mA
Load capacity: ≤500Ω
Power Supply:24V DC ±10% (standard)
