ABB

SPEED UP UNIT

Input Voltage:24 V DC
Power Consumption:≤ 8 W
Torque Response: ≤ 2 ms
Accel/Decel Rates: Up to 3x faster vs
Overload Capability: 200%
Type:Dynamic Performance Module 

Analog Input Board

Power Supply:24V DC (±10%) 
Power Consumption:≤ 4 W
Voltage: 0–10V
Current: 0–20mA
Resistance: Pt100/Pt1000 RTDC
Resolution:16-bit 
Sampling Rate：10 ms/channel
Voltage: ≥1 MΩ
Current: 250Ω ±0.1%
Channel-to-Channel: 300V AC
Channel-to-Backplane: 1500V AC

ANALOG INPUT BOARD

Power Supply:24V DC (±10%) 
Power Consumption:≤ 3 W
Input Channels:8x Isolated Voltage Inputs 
Resolution:16-bit 
Accuracy:±0.1% of FS (Full Scale) at 25°C
Input Impedance ≥1 MΩ
Sampling Rate:10 ms/channel
Channel-to-Channel: 300V AC
Overvoltage Protection:±30V continuous

Analog Input Module

Overload Protection:±30V (voltage)
Power Supply:24V DC 
Power Consumption:≤ 1.5 W
Input Channels:4x Isolated Channels
Voltage: 0–10V, ±10V, 0–5V
Current: 0–20mA, 4–20mA
Resolution:12-bit 
Sampling Rate:2 ms per channel
Voltage: ≥100 kΩ
Isolation:1500V AC 

DIGITAL INPUT CIRCUIT BOARD

Type:8-Channel Isolated 
Sink/Source: Auto-detecting
Voltage Range: 15–30V DC
Input Current 3–8 mA
Response Time:≤ 2 ms
Isolation:1500V AC 
Power Supply:24V DC
Power Consumption:≤ 1.8 W

Digital Output Module

Output Signal: 24V DC
Load Current per Channel:0.5A to 2A
Max Switching Voltage: 30V DC
Isolation Voltage: 500V AC/DC
Response Time: <1ms 

CURRENT FEEDBACK BOARD

Supply Voltage:24V DC 
Current Input :3-phase AC
Isolation Voltage:2500V AC
Frequency Range:0–500 Hz

Industrial Circuit Board

Power Supply:24V DC
Analog Inputs: 4-20mA
Digital I/O: Opto-isolated inputs
Communication: Possible RS-485/Modbus 
Type: Industrial control

IGITAL OUTPUT MODULE

DRIVE BOARD
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-FK
Number of Channels: Typically 4 or 8 
Switching Capacity: Up to 2A per channel 
Supply Voltage: 24V DC 
Isolation Voltage: 1500V AC
Response Time: <1ms

Digital I/O card

Input Voltage:24V DC nominal (15-30V range)
Input Current :3-5mA per point 
Output Type:Relay (Form C) or Solid State 
Output Rating:2A @ 30V DC
Isolation Voltage:1500V AC 
Response Time:<1ms (input)

INTERCONNECTOR

Contact Configuration:96-position (48x2 rows)
Contact Material:Gold-plated copper alloy
Current Rating:1A per contact (max)
Voltage Rating:60V DC max
Contact Resistance:<20mΩ (initial)
Insulation Resistance:>100MΩ @500V DC
Mating Cycles: >500 insertions

Industrial Control Board

Supply Voltage:24V DC ±10%
Power Consumption:15W (max)
Isolation Voltage:1500V AC (I/O to logic)
ESD Protection:±8kV (contact discharge)
Processor: 32-bit RISC-based
Memory: 16MB Flash,
I/O Capabilities:8x digital inputs (24V DC)

Industrial Control Board

Supply Voltage:24V DC ±10%
Power Consumption:20W (typical)
Processor:32-bit DSP (200MHz)
Memory:16MB Flash, 8MB RAM
Isolation Voltage:1500V AC (I/O to logic)

Advanced Control Module

Processor:Dual-core PowerPC @ 1.2GHz
Memory:2GB DDR3 RAM + 4GB Flash
Control Loops:Up to 256 PID loops
Scan Time:0.1ms (minimum)
Task Capacity:32 parallel tasks
Legacy Protocols: PROFIBUS-DP
Max Expandable I/O: 1024 points
High-speed analog:±10V/4-20mA

Communication Interface Module

Supply Voltage:24V DC ±10%
Power Consumption:8W (typical), 12W (max)
Isolation:2500V AC (port-to-port)
ESD Protection:±8kV (contact discharge)
Ethernet Ports:2x 10/100BASE-TX (RJ45)
Serial Interfaces:2x RS-485 (isolated)
Protocol Support:PROFIBUS DP-V1
Data Rate:Up to 12Mbps

Control Module

Supply Voltage:24V DC ±10%
Power Consumption:15W (typical), 25W (max)
Isolation Voltage:1500V AC 
ESD Protection:±8kV 
Control Loops: Up to 512 PID loops
Execution Time: 0.1ms for basic instructions
Task Capacity: 64 parallel tasks
Memory Cycle Time: <10ns

Pulse Amplification Board

Input Voltage Range:10mV - 30V AC/DC
Input Impedance:100kΩ (typical)
Output Signal:24V transistor / 0-20mA
Output Current:≤500mA (transistor), ≤20mA (analog)
Isolation Voltage:1500V AC 
High-gain amplifier: 10-100x adjustable
Wide input range: 10mV to 30V pulses
Frequency response: DC to 500kHz
Isolated output: 24V PNP/NPN or 0-20mA

Procontrol System Coupling Module

Voltage: 24 VDC (±15%) or 110–240 VAC
Power Consumption: 5–10 W
Operating Temperature: -20°C to +60°C.
Humidity: 5–95% non-condensing.

Control Board

Analog I/O update rate: 1 kHz
Digital I/O update rate: 10 ms
Standard range: -20°C to +60°C
Extended range: -40°C to +70°C 
Power consumption: Max. 10W
Humidity: 5% to 95% RH
16-bit resolution for analog inputs/outputs

CONVERTER PULSE BOARD

Input Voltage Range:5-30V DC (HTL)
Input Frequency:0-500kHz
Output Signal:Differential (RS422) or single-ended
Output Current:20mA max
Power Supply:24V DC ±10%
Power Consumption:5W typical
Resolution: Up to 4096 pulses/revolution
Signal Delay: <100ns

FIELD PROTECTION UNIT

Operating Time:<8ms for critical faults
Measurement Accuracy:±0.5% of reading
Sampling Rate:64 samples/cycle
Time Sync Accuracy:±1μs
Power Supply:48-125V DC or 90-264V AC
Power Consumption:15W typical
Isolation Voltage:2.5kV AC

LCDC Module

Supply Voltage: 24 VDC (±10%)
RS-232/RS-485 serial interface
Relay Outputs:0-24 VDC
Operating Temperature: 0°C to 55°C
Humidity: ≤95% non-condensing

I/O module

16 digital inputs (24V DC)
Configurable as sinking/sourcing
3ms debounce filtering
Channel-by-channel LED status
Voltage Range:5-30V DC
Current:3mA typical
Isolation:1500V AC 

I/O Module

Analog Input :4-20mA/0-10V
Analog Output:4-20mA/0-10V
Digital Input:24V DC
Digital Output:24V DC, 0.5A
Resolution:16-bit
Accuracy:±0.1% of span
Input Impedance:250Ω
Input Voltage:24V DC (15-30V range)
Output Current:0.5A max per channel
Response Time:<1ms
Backplane Interface: Redundant S800 I/O bus
Update Rate: 10ms (all channels)

Mini Contactor Relay

Rated Current (Ie):6A (AC-1)
Rated Voltage (Ue):230V AC / 24V DC
Breaking Capacity:3A @ 400V AC (AC-3)
Contact Material:Silver alloy (AgSnO₂)
Coil Voltage:24V DC / 48V DC / 110V AC / 230V AC (selectable)
Power Consumption:2.2W (DC) / 3.5VA (AC)
Operate Time:≤15ms (DC), ≤20ms (AC)
Release Time:≤10ms (DC), ≤15ms (AC)

83SR06E Binary and Analog Control Module

Overload (49):20-100% of In
Short Circuit (50):2-15×In
Phase Loss (46):Fixed/Adjustable
Ground Fault (51G):20-40% of In
Rated Current (In):6A (CT 5-100A)
Control Voltage:24-240V AC/DC
Contact Rating:5A @ 250V AC (resistive)
Communication:RS-485

Analog Output Module

Accuracy:±0.1% of span
Galvanic isolation:1500V AC channel
Range:4-20mA / 0-20mA
Resolution:16-bit
Load Capacity:≤750Ω
Update Rate:10ms per channel
Power Supply:24V DC ±10%
Power Consumption:5W (max)
Isolation Voltage:1500V AC

81EU01 Universal Input Module

81EU01 Input Module universal
16 fold for Binary and Analog Transmitters
ValueUnavailable
16 Channels

Analog Output Module

Range:4-20mA / 0-20mA
Resolution:16-bit
Accuracy:±0.05% of span
Load Capacity:≤750Ω
Update Rate:5ms per channel
Power Supply:24V DC ±10%
Isolation:1500V AC

Control Module

Channels:16
Voltage/Current:24V DC, 0.5A
Isolation:1500V AC
Response Time:<1ms
Power Supply:24V DC ±10%
Power Consumption:8W (typical)

83SR11E Module

Power Supply:24V DC ±10%
Power Consumption:6W (typical)
Isolation:1500V AC
Range:4-20mA / 0-20mA
Resolution:16-bit
Accuracy:±0.05% of span
Load Capacity:≤750Ω
Update Rate:5ms per channel

Analog Output Module

Power Supply:24V DC ±10%
Power Consumption:4W (typical)
Isolation:1500V AC
Range:4-20mA / 0-20mA
Resolution:16-bit
Accuracy:±0.1% of span
Load Capacity:≤750Ω
Update Rate:10ms per channel

Control Board

Power Supply:24V DC ±10%
Analog Input:4-20mA / 0-10V
Digital Output:Relay, 5A @ 250V AC
Overcurrent:5-100A
Ground Fault;1-10A
Protocol: Modbus RTU (RS-485)
Baud Rate: 1200-19200 bps

Coupler Module

Application:Interfacing a computer
Transmission:Serial acc. to RS 232c
Transmission rate:300 - 19200 baud
Transmission distance, max.:20 m

Industrial Control Board

Processor:Dual-core PowerPC @ 800MHz
Memory:64MB Flash, 32MB RAM
Control Loops:Up to 128 PID loops
Ethernet: 2x 10/100BASE-T
Serial: 1x RS-485
Fieldbus: PROFIBUS DP
Digital Input:24V DC
Digital Output:Relay, 2A @ 30V DC
Analog Input:4-20mA/0-10V

Coupling Module

Power Supply:24V DC ±10%
Power Consumption:5W 
Isolation:1500V AC
PROFIBUS Connector:9-pin D-sub
Protocol:PROFIBUS DP
Address Range:0-125
I/O Capacity:244 bytes input
Response Time:<1ms

Control I/O Module

Analog Input:4-20mA
Digital Input:24V DC, 3mA
Analog Accuracy:±0.1% of span
Digital Isolation:1500V AC
Update Rate:10ms (all channels)
Power Supply:24V DC ±10%
Power Consumption:8W (max)
Backplane Interface: S800 I/O bus

Analog Input Module

Power Supply:24V DC ±10%
Power Consumption:6W (max)
Isolation:1000V AC
Range:4-20mA
Resolution:16-bit
Accuracy:±0.05% of span
Input Impedance:250Ω
Update Rate:10ms/channel

Analog Input Module

Power Supply:24V DC ±10%
Power Consumption:8W (max)
Current:0-20mA/4-20mA
Voltage:0-10V/±10V
RTD:Pt100/Pt1000
Sampling Rate:50Hz/channel
Common Mode Rejection:>120dB @ 50/60Hz
Normal Mode Rejection:>60dB
Input Impedance:250Ω (current)

Joystick assy

Operating Voltage:Typically 24V DC
Analog:0-10V
Digital :CANbus/DeviceNet
Current Consumption:<100mA 
Degrees of Freedom:2 or 3 axes
Handle Material:Industrial-grade plastic/metal
Mechanical Life:>1 million cycles
Operating Force:3-10N 

Coupling Module

Power Supply:24V DC ±10%
Power Consumption:5W (typical)
Isolation:1500V AC
Protocol:PROFIBUS DP
Data Rates:9.6kbps - 12Mbps 
Address Range:0-125
Response Time:<1ms

Digital Output Module

Power Supply:24V DC ±10%
Power Consumption:4W (typical)
Isolation:500V AC (channel-to-channel)
Backplane Current:100mA (max)
Output Voltage:24V DC
Output Current:0.5A per channel 
Switching Frequency:Up to 100Hz

Digital Output Module

Power Supply:24V DC ±10%
Power Consumption:5W (max)
Isolation:500V AC 
Backplane Current:120mA (max)
Output Type:Solid-state 
Output Voltage:24V DC 
Output Current:0.5A per channel
Switching Frequency:Up to 100Hz
Leakage Current:<1mA

Binary Input Module

Power Supply:24V DC ±10%
Power Consumption:3W (typical)
Backplane Current:80mA (max)
Update Rate:10ms
Input Type:Sink/Source (configurable)
Input Voltage:12-60V DC
Threshold Voltage:8V DC (ON), 5V DC (OFF)
Input Current :3mA @ 24V DC
Response Time:<1ms
Isolation :1500V AC

Station bus coupling module

Power Supply:24V DC ±20% 
Power Consumption:15W (typical)
Isolation:1500V AC 
Data Rates:10/100 Mbps
Latency: <100μs 
I/O Capacity:Up to 1024 signals

Universal Control Module

Memory:128MB Flash
Control Loops:Up to 64 PID loops
Scan Time:<1ms
Analog Input:4-20mA/0-10V
Digital Input:24V DC, 3mA

Analog Input Module

Power Supply:24V DC ±10%
Power Consumption:8W (max)
Sampling Rate:50Hz/channel
CMRR:>120dB @ 50/60Hz
NMRR:>60dB
Input Impedance:250Ω

Industrial Control Panel

Input Voltage:400-480V AC 3-phase (50/60Hz)
Control Voltage:24V DC ±10%
Main Circuit Breaker:80A (adjustable)
Short Circuit Rating:65kA @ 480V AC
Power Consumption:≤500W 

Analog Input Unit

Power Supply:24V DC ±10%
Power Consumption:5W (typical)
Current:4-20mA/0-20mA
Voltage:0-10V/±10V
RTD :Pt100
Sampling Rate:10ms/channel
Common Mode Rejection:>100dB @ 50Hz
Input Impedance:250Ω 

Bus Coupling Module

Power Supply:24V DC ±10%
Power Consumption:5W (typical)
Isolation :1500V AC 
Protocol :PROFIBUS DP 
Data Rates:9.6kbps to 12Mbps 

Transducer Board

Power Supply:24V DC ±10%
Power Consumption:5VA (max)
Isolation:2kV AC (input-to-output)
Voltage Input:0-690V AC 
Current Input:0-5A AC (via CTs)
Frequency Range:45-65Hz
Input Impedance:>1MΩ (voltage)
Analog Outputs:2x 4-20mA 
Accuracy:±0.5% of span
Load Capacity:≤500Ω

IGBT Module

Voltage Ratings:1700 V
Current Ratings;450 A
Power Dissipation:2-3 kW
Switching Frequency Range: Up to 5-10 kHz
Isolation Voltage:2500-4000 V

GATE POWER UNIT

Model: KUC755 AE106
Order/Part Number: 3BHB005243R0106
Description: Gate Power Unit 
Input Voltage: Typically 24V DC
Output Gate Drive Voltage: ±15V to ±20V 
Output Current: Up to 5A peak
Isolation Voltage: ≥2500V AC

Converter Display Board

Supply Voltage: 24V DC
Power Consumption: <5W
Part Number: 3BHB006943R0002
Supported Languages: Multiple
Alternative Designation: UNS0885A-Z, V2
Description: Display and control interface board

Power Supply

Input Voltage Range:85–264V AC
Frequency Range: 47–63Hz
Inrush Current: ≤20A
Efficiency: ≥90%
Output Voltage: 24V DC
Output Current: 5A 
Power Rating: 120W
Overload Protection: 105–150% of rated current 

Ethernet POWERLINK adapter module

Supply Voltage: 24V DC
Power Consumption: ≤5W
Isolation: 1500V AC
Cycle times :≤200 µs
Protocol: Ethernet POWERLINK

Electro-Pneumatic Positioner

Low operating cost 
Compact design 
For SIL2 safety loops
Mechanical position indicator 
Well-proven technology and intelligence 
Robust and environmentally ruggedized
ATEX, FM, CSA, GOST and IECEx approvals
Wide operating temperature range -40 ... 85 °C

MLink Control Unit

Communication Gateway
Product Main Type:MLink
Hardware Version 2
Internal: Modbus TCP 
Fieldbus: Profibus, Modbus RTU/TCP, PROFINET IO

Memory Card

Order Number: 3BHE017400R0101
Memory Type: Flash memory
Capacity: 1GB
Write Cycles: 100,000 minimum
Interface: CompactFlash (CF)
Supply Voltage: 3.3V ±5%
Data Transfer Rate: Up to 16MB/s

Processor board

Power Supply: 24V DC ±10%
Power Consumption: 15W typical
Isolation: 1500V AC 
RAM: 512MB
Flash Memory: 128MB
Memory Card Slot: Supports PPD104 CF card
Ethernet Ports: 2x 10/100/1000 Mbps
Serial Port: 1x RS-232/485

Power Supply Board

3-phase: 380-500V AC 
1-phase: 200-240V AC
Frequency Range: 47-63Hz
DC Bus Voltage: 510-620V DC
Rated Power: 11kW 
Overload Capacity: 150% for 60 seconds
Inrush Current Protection: <25A for 10ms
Efficiency: >95%
Undervoltage Lockout: <300V DC input

INTERFACE BOARD

Channels: 16
Voltage: 24V DC
Isolation: 1500V AC 
Type: 4-20mA/0-10V
Resolution: 16-bit
Field-to-system: 2500V AC
Channel-to-channel: 500V AC

POWER SUPPLY BOARD

Input Voltage Range:380-500V AC 
Optional: 200-240V AC
Frequency Range: 47–63Hz
Inrush Current Protection: <30A
Output Voltage: 24V DC
Rated Current: 10A
Power Rating: 240W
Ripple Noise: <100mV peak-to-peak
Overload Capacity: 150% for 5 seconds

Six-axis motor

Rated Power: 7 kW
Rated Speed: 3000 RPM (Variable Speed)
Rated Voltage: 400 V (3-phase AC)
Rated Current: 14 A
Rated Frequency: 50 Hz
Torque Constant: 20 Nm/A
Service Factor: 1.5 

Motor Control Card

Supply Voltage: 24V DC ±10%
Power Consumption: 15W typical
Isolation: 2.5kV input-to-output
PWM Frequency: 2-16kHz
Analog Inputs:4 channels
Digital Inputs:8 channels
Power Range: 0.5-800kW
Max Motor Speed: 6000 rpm