ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
ABB are a market leading producer of power & automation technologies that enhance performance and reduce environmental impact for industries worldwide.
Amikon Limited stock and supply ABB motors, drives, programmable logic controllers (PLCs), power electronics and Robot spare parts and Discontinued card parts, motion and obsolete including variable speed drives, DC drives, PLCs and general automation spares.
Input Voltage: +5V, +12V
Current Consumption: Typically under 2A
RS-232/RS-485
Operating Temperature: 0°C to 50°C.
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 85% (non-condensing)
Power Supply: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Number of Channels: 8
Current Output Range: 4-20mA
Voltage Output Range: 0-10V
Resolution: 16-bit
Accuracy: ±0.1% of span
Current: ≤750Ω
Voltage: ≥1kΩ
Input Voltage:24V DC nominal
Input Current:3-8mA per channel
Isolation:1500V AC (field to logic)
Response Time:<1ms (ON/OFF)
Number of Channels:32
Voltage Rating:1600V (V_RRM)
Current Rating:300A (I_FAVM)
Surge Current:8kA (I_FSM, 10ms)
Forward Voltage:1.25V @ 300A (typical)
Range: Typically 4-20 mA
Input Impedance:≤ 10 Ω
Load Capacity: Standard 0-500 Ω
Voltage: 24 V DC
Test Voltage: Typically 1.5 kV AC
Typical: ±0.1% of full scale
Communication Interface:RS-232, RS-485
Data Transfer Speed:Up to 115,200 bps
Power Supply:24V DC
Mounting Type:DIN rail mounted
Operating Temperature:-20°C to 60°C (-4°F to 140°F)
Storage Temperature:-40°C to 85°C (-40°F to 185°F)
Humidity Tolerance:5% to 95% non-condensing
Voltage: 125 VDC Nominal
Power Consumption: Typically < 5W
Input-to-Input: 1500 VAC min.
Input-to-Output/Logic: 1500 VAC min.
Output-to-Output: 500 VAC min.
Output/Logic-to-S+ I/O: 500 VAC min
Rated Voltage:400 V AC (3-phase, 4-wire)
Rated Current:22 A (continuous)
Rated Frequency:50/60 Hz
Transfer Time:< 100 ms (typical for open transition)
Withstand Current:10 kA (IEC 60947-6-1)
Mechanical Life:10,000 cycles (minimum)
Number of Positions:10 Position
Pitch:9.53 mm
Current Rating:30 A
Voltage Rating:300 V
Wire Gauge Min:22 AWG
Wire Gauge Max:14 AWG
Type:Terminal Block
Number of Rows: 2 Row
Mounting Style:Panel Mount
Protocol: PROFIBUS DP-V0
Data Transfer Rates:up to 12 Mbp
Connector Type: 9-pin D-sub
Electrical Interface: RS-485
Voltage: +5 V DC
Power Consumption: 1-2 W
Max. Input Data (to Master): Up to 244 bytes per cycle
Max. Output Data (from Master): Up to 244 bytes per cycle
Protocol: PROFIBUS DP-V0 Data Transfer Rates:up to 12 Mbp Connector Type: 9-pin D-sub Electrical Interface: RS-485 Voltage: +5 V DC Power Consumption: 1-2 W Max. Input Data (to Master): Up to 244 bytes per cycle Max. Output Data (from Master): Up to 244 bytes per cycle
CPU Type: 32-bit RISC-based processor
Clock Speed: 100–200 MHz
Program Memory: Up to 4 MB Flash
Data Memory: Up to 2 MB RAM
Execution Speed: 0.1 ms
Input Voltage: 24V DC
Resolution: 12-bit to 16-bit
Channels:8/16 DI or DO
Input Voltage:24V DC
Output Type:Relay/Transistor
Isolation:1.5kV AC
PROFIBUS DP (via coupler)
Modbus RTU (RS-485)
EtherNet/IP (optional)
Collector-Emitter Voltage (Vces):1200V
Collector Current (Ic @ 25°C):450A
Collector Current (Ic @ 80°C):300A
Pulse Current (Icm):900A
Power Dissipation (Ptot):1800W
Gate-Emitter Voltage (Vges):±20V
Turn-on Delay Time (tdon):110ns
Rise Time (tr):50ns
Turn-off Delay Time (tdoff):400ns
Fall Time (tf):120ns
Switching Frequency:Up to 20kHz
Supply Voltage: 24V DC (19.2-30V DC)
Power Consumption: 1.5W
Current Capacity: 6A
Isolation Voltage: 500V AC
Fieldbus Protocol:PROFIBUS DP-V1
Data Rate:Up to 12 Mbps
Address Range:1-125 (PROFIBUS)
I/O Connection:S800 I/O bus
Microprocessor-based protection
Three-phase trip-free mechanism
Front-connected auxiliary contacts
Integrated earth fault protection
Remote control and monitoring capabilities
High-performance AC800F platform
Supports a wide range of I/O modules
Supports a variety of programming languages
Suitable for a wide range of industrial applications
Compact and modular design
Voltage Input: 380V to 690V AC (3-phase)
Switching Frequency: 2–16 kHz range
Operating Temperature: -10°C to +50°C (ambient, typical)
Humidity: ≤95% non-condensing
Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs
Memory:32MB SDRAM
Control Loop Time:100μs (speed)
Digital I/O:12x 24V DC inputs
Supply Voltage:24V DC ±10%
Power Consumption:15W max
Isolation:2500V AC
Data rate: 10 Mbps
Max. distance: 100m (fiber length)
ModuleBus connection to AC 800M
Supply voltage: 24 VDC (±10%)
Power consumption: <5 W
Isolation: 1500 VAC
Supports up to 12 drives per module
Power Supply:24V DC (±10%)
Tachometer input: 0-10V DC or 4-20mA
Pulse input: Up to 100kHz frequency
Analog output: ±10V DC or 4-20mA
Relay outputs: 2x SPDT (5A @ 250V AC)
Speed Range: 0-10,000 RPM (configurable)
Resolution: 0.1% of full scale or better
Digital outputs: 24V DC, 0.5A
Voltage: 0-10V DC, ±10V DC
Current: 4-20mA, 0-20mA
Load Capacity:Voltage: ≥1kΩ
Isolation:1500V AC channel-to-channel
Backplane Power: 5V DC @ 500mA (typical)
Field Power: 24V DC (±10%) for outputs
Power Consumption: 6W (typical)
Voltage Rating: 1200V–1700V
Input Voltage (DC Link): 300–1000V DC
Output Voltage (AC): 3-phase, 0–480V AC
Current Rating: Up to 500A
Switching Frequency: 2–20 kHz
16 channels for 24 V d.c.
Redundant or single configuration
Output status indicators
Advanced on-board diagnostics
Degraded mode for normally energized channels
I/O Capacity:16 digital inputs (24V DC)
Processing Speed: 1ms scan time (typical)
Memory: 64KB SRAM
Power Supply:24V DC (±10%)
Consumption: 5W (typical)
Isolation:1500V AC (channel-to-channel)
Input Voltage: 24V DC (±10%)
Power Consumption: 5W–10W (typical)
Isolation: 500V AC (channel-to-bus)
Processor: DSP or FPGA-based
Flash: 8MB–16MB
Digital I/O: 8–16 channels
DeviceNet or Profibus
RS-232/RS-485
Operating Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Signal Isolation: 2500V AC
Switching Frequency: Up to 20kHz
Gate Drive Outputs:±15V gate drive voltage
Input Voltage:24V DC (±10%) or 115/230V AC
Output Voltages:+5V, ±15V, +24V DC
Power Capacity:100W (max)
Inrush Current:15A (for 20ms at 230V AC)
Efficiency:>90% (at full load)
Fiber-Optic Signal Isolation :2500V AC
Voltage Rating:1700V
Current Rating:450A (continuous)
Max Junction Temp.:150°C
Switching Frequency:Up to 5kHz
Gate Drive Voltage:+15V/-5V
Isolation Voltage:2500V RMS
Power Consumption:25W (typical)
Protection Response:<2μs (short-circuit)
Input Voltage:3-phase 380-480V AC (±10%)
Output Voltages:+24V DC (control)
Power Capacity:500W (continuous)
Switching Frequency:20kHz (PWM)
Efficiency:>92% (at full load)
Input Voltage:24V DC (±10%)
Power Consumption;25W (typical)
Isolation :1500V AC (field to logic)
Vector control
Torque/speed regulation
PID controllers
Communication;Ports2x Ethernet, 1x RS-485
Input Voltage:24V DC (±10%)
Power Consumption:8W (typical)
Isolation Voltage:1500V AC (channel-to-channel)
Communication Speed:Up to 1Mbps
Signal Channels:16 digital I/O
Voltage Rating:1200V
Current Rating:300A (continuous)
Max Junction Temp.:150°C
Switching Frequency:Up to 20kHz
Gate Drive Voltage:+15V/-5V
Isolation Voltage:2500V RMS
Protection Features:DESAT, UVLO, OT
Response Time:<2μs (short-circuit)
Voltage Rating:24V DC (±10%)
Current Draw :0.8A (max)
Power Consumption:19.2W
Startup Voltage:≤18V DC
Airflow:340 CFM (5.7 m³/min)
Static Pressure:120 Pa
Speed:3200 RPM (±10%)
Noise Level:55 dB(A) at 1m
Power Supply:24V DC (±10%)
Power Consumption:8W (typical)
Response Time:<1ms (input), <0.5ms (output)
Surge Protection:30V DC
Channels:16x digital
Voltage Range:24V DC (±10%)
Current Rating:5mA (min)
Isolation:1500V AC
Rated Voltage:690V AC
Current Rating:44A continuous
Short-Circuit Capacity:50kA (1s)
Power Connections:4-in/8-out configuration
Isolation Voltage:3000V AC
Operating Voltage:24V DC (±10%)
Power Consumption:2W (typical)
Signal Range:0–24V DC, 4–20mA
Resolution:12–16-bit
Short-Circuit Protection:Self-resetting fuse
POWER MASTER BOARD
VOLTAGE DRIVE CROWBAR CIRCUIT BOARD
Input Voltage:24V DC (±10%)
Output Voltage:0-10V (Programmable)
Current Rating:2A (Max Continuous)
Frequency Range:0-400Hz
Isolation Voltage:1500V AC
Maximized operating time
Ensures safe machine operation
Guarantees the quality of delivered energy
Seamless integration with the power plant control systems
Function:PROFIBUS master
Communication Protocol:PROFIBUSMaster
Communication Interface:Serial
Number of Hardware Interfaces:RS-485 1
Data Transmission Rate:12000 kbit/s
Degree of Protection:IP20
Rechargeable lithium-ion battery
3.7V, 2,4Ah
Non-restricted
Common recommendations for storage of Li-ion batteries
are at -20° to 25° C and to charge the batteries once
per year to 40% (or 3.75V/cell) of their capacity and
never let them discharge to below 2.0V
Supply Voltage:24V DC (±15%)
Power Consumption:1.8W (typical)
Interface:9-pin D-Sub
Bus Termination:Integrated
Bus Protocol:PROFIBUS DP (EN 50170)
Transmission Rate:9.6Kbps to 12Mbps
Address Range:0-125
Max Number of Slaves:125
Electrical Isolation:500V AC
Asymmetric Integrated GateCommutated Thyristor
VDRM = 4500 V , ITGQM = 4000 A
Mounting force 40kN
High snubberless turn-off rating
Optimized for medium frequency
High electromagnetic immunity
Simple control interface with status feedback
AC or DC supply voltage
Option for series connection
Reverse Conducting Integrated Gate-Commutated Thyristor
VDRM = 4500 V ,ITGQM = 3600 A ,ITSM = 20·10³ A
VT0 = 1.24 V , rT = 0.51 mΩ ,VDC = 2800 V
Mounting force 41kN
High snubberless turn-off rating
Optimized for medium frequency
High electromagnetic immunity
Simple control interface with status feedback
AC or DC supply voltage
Option for series connection
Model Number:NBRC-61C (61357246F)
Type:Chopper Control Board
Operating Voltage:24V DC (±10%)
Power Consumption:8W (typical)
Signal Levels:0-10V analog, 24V digital
Isolation Voltage:1500V AC (input-to-output)
PWM Frequency:2kHz (adjustable)
Current Regulation:±1% of setpoint
Response Time:<5ms (90% step change)
Resolution:12-bit (analog signals)
Processor:Dual-core 1.2GHz
Memory:2GB DDR3 RAM
Storage:8GB Flash
Execution Speed:10ms cycle time (typical)
Operating Voltage:24V DC (±10%)
Power Consumption:15W (typical)
Isolation Voltage:1500V AC (field to system)
