Series:Series 90-70
Manufacturer:GE Fanuc; Emerson Automation (Current)
Part Number:IC697MDL750
Rated voltage:24 to 48 Volts DC
No of Channels:Thirty-Two (32)
No. of output groups:Four (4)
Channels per group:Eight (8)
Current draw:0.25 A
Required current:0.25 Amps
Wiring configuration:Positive Logic
Output voltage range:20-60 VDC
Number of outputs:32
On response time, maximum:1 ms
Off response time, maximum:1 ms
Output signal range:20 - 60 VDC
Isolation voltage:1500 Volts
Series:RX3i PacSystem
Part Number:IC695PMM335
Catalog:IC695
No. of Axes:4
No of Master axes:1
Backplane Support:Universal Support
Motion Path Planning:1ms
Number of Slots:1 (single slot)
Position Loop Update Rate:500μs
Controlled Axes/Module:4
FSSB Velocity Loop Update Rate:125μs
Motion Path Planning:1 ms
FSSB Torque Loop Update Rate:62.5μs
Power Consumption at 5 V:0.45 A
Servo Command Interface:Fiber Optic
Power Consumption at 3.3 V:1.1 A
Floating Point:Yes
Input Voltage: 24V DC
Current Consumption: 1.5A typical
Isolation: 1500V AC channel-to-channel
Trip Contact Ratings:5A @ 30V DC resistive
Analog Inputs: 8 channels
Relay Outputs: 8 channels
Communication Ports: 2x Ethernet for diagnostics
Power Supply:28VDC
Functional Revision 1:A
Mark VI Series Grouping:Group 1
Number of Channels:16 (isolated)
Input Type:Dry contact (volt-free) or wet contact (24–125V DC)
Voltage Range:24–125V DC (configurable)
Input Current :2–20mA per channel
On-State Voltage:≤3V DC (for dry contact)
Off-State Leakage:<1mA
Series:PACSystem RX3i
Manufacturer:GE Fanuc
Part Number:IC694MDL240
Description:Input module
No of Channels:Sixteen (16)
Points:16
Input signal range:0-132 VAC
Voltage:120 Volts AC
Nominal Input voltage:0-120 VAC
Current:7 milliamps
Input Frequency:47-63 Hz
Power consumption:90 milliamps
Input current:12mA per channel
Input current:12 mA
Bus voltage:5 Volts
Current draw:90 mA (all inputs active)
Off response time, maximum:45 ms
On state current:6 mA
On response time, maximum:30 ms
Product Lifecycle Status:Active
Off state current:2.2 mA
On–state Current:6mA minimum
On response time, typical:30 ms
Channels:16x isolated
Voltage Range:24-125V DC
Current Rating:5mA (min)
Isolation:1500V AC
Power Supply:24V DC (±10%) from backplane
Power Consumption:6W (typical)
Response Time:<1ms (input), <0.5ms (output)
Contact Rating:50,000 operations @ rated load
Series: Mark VI
Product Type: Vibration Transducer Interface Module
Board rating: 125 V dc
Common Mode Voltage Range: ±5 V
Dimensions: 11.00 x 9.00 x 3.00
Operating temperature: 0 to 60 °C
No.of Analog Voltage Inputs: 6
Compatible:System RX7i system
Part Number:IC698ETM001
Series:Rx7i PACsystem
Brand:GE Fanuc
Speed:200 MHz
Voltage:5 Volts DC
Current:1.2 Amperes
Connector:10 Base T/100 Base Tx, RJ 45
Maximum Number of IP Addresses:One
