Operating Voltage:24V DC (±10%), 3W typical
Accuracy:±0.5% of full scale
Resolution:0.1% (for bargraph display)
Update Rate:100 ms
Isolation: 1.5 kV AC
MODE Switch: Toggle MAN/AUTO/CAS
Control Platform:32-bit RISC processor with FPGA logic
Control Methods:DTC , Scalar, Vector
I/O Capacity:16x DI
Operating Voltage:24 V DC (±10%)
Power Consumption:25 W (typical)
Memory:2 GB Flash (firmware/logs)
Rated System Voltage:3300V AC (2.3–4.16 kV range)
DC Link Voltage:5600V DC (max)
IGCT Control :24x Gate driver channels
Gate Drive Voltage:+20V / -5V
Auxiliary Power:24V DC (±10%), 150W
Isolation Voltage:6 kV AC
Response Time:<2 µs
Product Type : Power Supply Module
Model : SPW481 =
100-120V AC Input Power Supply Module
Standard type with no explosion protection
With ISA Standard G3 and temperature (-20C - 70C)
Input Channels :16 Channels
A/D Converter Resolution:16 bits
Input Range:1 4-20 mA only (through 200 Ω)
Normal Mode Rejection Ratio, at 60 Hz:19 dB
Maximum Normal Mode Input: ± 30 Volts
Crosstalk, dc to 60 Hz (channel-to-channel):-60 dB
Input Scan Rate:50 ms
Power supply:24V DC
Rated Current:55mA at 24V
Power Consumption:1.32W at 20mA
Power/DCS to Field:1500 VAC
DCS side connections:
37 pin DSUB connector on CC-UGIA01
Voltage Input:24V DC
Interface to DCS:4 to 20mA with HART
Number of input channels 16 channels, module isolation
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C
Withstand voltage 1.5 kV AC between input signal and system for 1 minute
Generator Voltage:100–690V AC (50/60 Hz),
Field Voltage (Output):10–250V DC
Regulation Accuracy:±0.5%
Response Time:<30 ms
Auxiliary Supply:24/48/110/250V
Power Consumption:≤25 W (standby)
Number of inputs 16-channel, module isolation
Input current 6 mA ± 20 %
Contact rating 24 V DC +20 % / -10 %
External power supply 24 V DC +20 % / -10 %
Input response time 40 ms maximum
Withstand voltage (*1) (*2) 2 kV AC
between input signal and system for 1 minute
16-input line collectivelyconnected
Input Voltage: Typically 24V DC
Output Signals: Digital and analog signals for
motor control and feedback.
Current Consumption:100-500mA
Communication Voltage Levels: 3.3V or
5V logic levels for digital communication.
DCS880
SDCS-CON-H01
Main Control Board
Operating Voltage:24 V DC (±10%)
Current Consumption:≤1.5 A
Digital I/O Channels:32 optoisolated DC I/O points
Analog I/O:±10 V DC / 4–20 mA
900C75S0560
CPU CONTROLLER
CONTROLEDGE
CPU: 32/64-bit microprocessor
RAM: 512 MB – 2 GB
Flash Storage: 4–8 GB
Input Voltage: 24 V DC
Power Consumption: ≤25 W
Isolation: 1500 V A
Ethernet Ports:8+ ports
Redundant Power Inputs:Dual 24 V DC terminals
Switching Capacity:Up to 24 Gbps
Input Voltage:24 V DC
Power Consumption:10–15 W
Isolation:1500 V AC
