
Power Entry Panel Dual Chassis
PHARPSPEP21013
Power Entry Panel
Dual Chassis Design
Typically supports AC or DC input, depending on the application
Appropriate current based on load requirements
ACS800 R2 to R6 STO Frequency Converter
Safety Category:Category 3 (EN 954-1)
Response Time:≤ 20 ms
Supply Voltage:24 V DC ±10%
Power Consumption:≤ 2 W
Input Signal:24 V DC (Pulse test: 0.5 Hz, 1 ms)
Input Current:6 mA per channel
Isolation Reinforced isolation : 500 V AC
IGCT Module
Blocking Voltage 4500 V DC
Reverse Voltage:30 V
Max RMS Current:4000 A
Peak Surge Current :32 kA
Turn-On Time: ≤ 3 µs
Turn-Off Time: ≤ 5 µs
Switching Loss: ≤ 15 kJ/s at 500 Hz
CONVERTER POWER BOARD
3-phase AC: 380–480 V AC
DC Bus Voltage:520–720 V DC
Power Rating:Typically 1–50 kW
Operating Temperature:-10°C to +50°C
Storage Temperature:-40°C to +85°C
Memory Board 8MB
Memory Type:Fast Page Mod
Battery Backup:Integrated 3.6V Lithium Battery
Capacity:8 MB SDRAM
Data Retention:≥72 hours
Interface:96-pin DIN 41612 connector (Type C)
Communication Module
Order Code:3BHE019958R0101
Functional Designation:UA D206 A
Power Supply:5 V DC
Consumption: 500 mA (max)
Data Rate:300 bps – 115.2 kbps (per port)
Isolation:500 V AC
Interface Module
Signal Channels:16 single-ended analog inputs
Voltage: ±10V, ±5V, ±1V, 0–10V
Current: 4–20mA, 0–20mA
Resolution:16-bit (including sign bit)
Accuracy:±0.05% of full scale (25°C)
Sampling Rate:10 ms/channel
Input Impedance:>1 MΩ
Overvoltage Protection:±30V continuous
Common-Mode Rejection:>120 dB at 50/60 Hz
Control Board
Clock Speed 800 MHz
Memory:128 MB NOR Flash
Backplane Interface:PCI-104
Power Requirements:5V DC @ 3.5A
Vibration: 5g @ 10–500Hz
Millmate Controller
Processor: 1.2 GHz
Power Supply: 24V DC ±10%
Power Consumption: 120W
MTBF: >200,000 hours
Control Loop Speed: 0.5–5 ms (configurable)
Max I/O Points: 5,000 digital / 2,000 analog
Communication Module
Supply Voltage: 5V DC
Power Consumption: 1.2A @ 5V DC (6W)
2× RS-485 ports (9-pin D-sub male).
Baud Rate: 9.6 kbps to 12 Mbps (auto-detect)
Max Stations: 125 slaves per segment
Redundancy Switchover: < 100 ms
Analog Input Module
Function:16 AI: U, I, RTD, DI
Number of Analog Configurable I/Os:0
Analog Inputs:16
Input Signal:U, I, RTD, DI
Resolution:Analog Input 13 bit
Degree of Protection:Housing IP20
Supply Voltage:24 V DC
Ambient Air Temperature:
Operation 0 ... +60 °C
Storage -40 ... +70 °C
Robot spray accessory controller
Supply Voltage: 24V DC (±10%), 5A max.
Atomization air pressure control
Fluid flow regulation (via PWM or analog valve)
HV electrostatic control (up to 100 kV)
Solvent purge management
Diagnostic monitoring (clogs, pressure faults)
Power Consumption: 120W (peak)
Panel unit
Module Slots: 8 slots for S800 I/O modules
Orientation: Vertical
Bottom/top gland openings
(M20/M25 cable glands)
Knockouts for field wiring
Binary In/Out Module
Input Impedance: 3-5 kΩ (High Range)
Maximum Continuous Voltage: 300V DC.
Maximum Surge Voltage: 1 kV, 1.2/50 µs waveform.
Operating Time: < 5 ms.
Release Time: < 5 ms.