Acceleration Range: ±2g, ±5g, ±10g, or ±50g
Voltage output, typically 0-5V or 0-10V
Supply Voltage: 5V DC or 12V DC
Operating Temperature: -40°C to +85°C
Universal Input Output IOTA
Input Channels 1 16 Channels
Common Mode Voltage, dc to 60 Hz -6 to +5 V peak
A/D Converter Resolution 16 bits
Normal Mode Rejection Ratio, at 60 Hz 19 dB
Normal Mode Filter Response Single-pole RC, -3 dB @ 6.5 Hz
Input Impedance (voltage inputs) > 10 M Ω powered
Input Scan Rate 50 ms
Supports fiber-optic medium
NFPA Class B or Class A operation
Data is immune to all environmental noise
Optical isolation prevents ground loops
High-Speed NFN fiber-optic medium
Fiber type: 62.5/125 micrometers (multi-mode);
50/125 micrometers (multimode),
or 9/125 micrometers (single mode)
Maximum attenuation: 10 dB with 62.5/125 μm cable, 6
Module Type:Central Processing Unit
Number of Slots:1 (Single slot)
Battery-backed memory: 1 Mbyte
Number of Points:12K discrete inputs and outputs
Serial Ports:1 (RS422/485 compatible)
Current Required:3.3 Amps nominal
8-Wide I/O
Interface Carrier
with Carrier Shield Bar
Operating temperature-40 to 70°C (-40 to 158°F)
Storage temperature-40 to 85°C (-40 to 185°F)
Relative humidity5 to 95%, non-condensing
3300 XL 8 mm Probe
M10 x 1 thread
with armor
10 1.0 meter (3.3 feet)
01Miniature coaxial ClickLocconnector
with connectorprotector, standard cable
00 Not required
For use in Tight
Installation Requirements
Replaces 3300 RAM Transducer Systems
and 3000-Series or 7000-Series 190 Transducer System
Average Scale Factor of 7.87 V/mm (200 mV/mil)
For use in Tight
Installation Requirements
Replaces 3300 RAM Transducer Systems
and 3000-Series or 7000-Series 190 Transducer System
Average Scale Factor of 7.87 V/mm (200 mV/mil)
Device short name:BMH
Maximum mechanical speed:8000 rpm
Range compatibility:Lexium 32
rated supply voltage:240 V
Continuous stall current:5.55 A
Continuous power:1.68 W
Maximum permanent current:17.84 A
Holding torque:3 N.m holding brake
Torque constant:0.61 N.m/A at 120 °C
Back emf constant:39.3 V/krpm at 120 °C
Range Compatibility:PacDrive 3
Maximum mechanical speed:9000 rpm
Continuous stall current:0.73 A
Continuous power:290 W
Maximum current Irms:2.9 A
Speed feedback resolution:128 periods
Torque constant:0.58 N.m/A 248 °F (120 °C)
Back emf constant:40 V/krpm 68 °F (20 °C)
Power Supply:24VDC
No. of Inputs:(10) 24V dc; (4) fast 24V dc
Input Circuit Type:24 VDC
Output Circuit Type Relay; FET
Relay Contact Rating:24-125VDC; 120-240VAC
Power Supply Usage:82 VA
Input Power:24V DC
Inputs:(10) 24V DC and (4) Fast 24V DC
Type:FT color
Diagonal:10.4" (264 mm)
Resolution:VGA, 640 x 480 pixels
Buffer time:10 min
Variant:Lithium ion
Clock frequency:266 MHz
L1 cache:16 kB
Flash:2 MB (for firmware)
Cooling:Passive via heat sink
Mode/Node switches:2, 16 positions each
Accuracy At 25°C: Typ. 10 ppm (1 second) per day
Controller:SMC
Range of measurement: from 100N to 2kN
Accuracy class: 0.5%
Corrosion resistant
STRAIN AND FORCE SENSOR
TR FORCE TRANSDUCER FOR
MEASURING SPINDLES TENSION
Range Compatibility PacDrive 3
Device short name SH3.....P
Maximum mechanical speed 8000 rpm
rated supply voltage 115...480 V
Continuous stall current 1.8 A
Continuous power 690 W
Maximum current Irms 5.7 A
Speed feedback resolution 128 periods
Series Type:Low-inertia
Voltage Class:400 Volts AC
Frame Size:63 millimeters
Magnetic Stack Length:3 inches
Rated Speed:7000 rpm
Feedback:Multi-turn high-resolution encoder
Shaft Key/Seal:Shaft key/no shaft seal
Brake:24 Volts DC brake
