ALL MANUFACTURERS

Analog Output 24V IOTA Module

Typically 24V DC or 12V DC
Output Type Source 
Load Voltage 15 30 VDC Maximum
On-State Voltage 24 V (typ), load current @ 0.5A
Off-State Leak Current 5.0 µA (max)
Turn-On/Turn-Off Time 10 ms (max)

Communication Module

Output Expansion Termination Module

Series Mark V
Part Number DS200DTBDG1ABB
Functional Acronym DTBD
Functional Description Mark V Terminal Board
PCB Coating Normal Coating
Revision Quantity 3 Revisions
Mark V Series Grouping Group 1
Assembly Type Normal Assembly

Analog Input Milliamp I/O Termination Module

Mark V Series
Functional Description RST 
Analog Termination Board
Functional Acronym TBQC
PCB Coating Normal Coating
Functional Revision 1 A

Serial Interface Card

Local Bus Power 12 VDC at 300 mA
AmbientTemperature-40°C to +70°C 
Shock 10g ½ Sinewave for 11msec
Vibration 1mm Peak to Peak from 2 to 13.2Hz
0.7g from 13.2 to 150Hz
AirborneContaminantsISA-S71.04 –1985 Airborne
Contaminants Class G3 

Vibration Transmitter

05 0-5 mils pp (0-125 μm pp)
03 DIN clips and screws
CNCSA Division 2, ATEX Zone 0
ATEXZone 2 and includes 
ABSmaritime approval

SIMATIC SCD1900 19"WIDE/TOUCH/1440X900

RX3i High Speed Counter, 4 channels. 8 configurable inputs and 7 configurable ESCP outputs. Module supports high speed counting, input interrupts and programmable limit switch.

Analog input 15 bit, 4-20mA, current, 15 channel. TUV approved.

I/O Module

Description: I/O Module 
Compatibility: 3500 Series
Analog Inputs: 4–20 mA, 0–10 V
Power Supply: 24 VDC
Operating Temperature: -40°C to +85°C (-40°F to +185°F)
Humidity Tolerance: Up to 95% non-condensing

Condition Monitoring System

Input Power Min: 18 Vdc Max: 36 Vdc 
Current Max: 1.7 A 
InrushCurrentMax: 2.7 A, less than 5 ms 
Max: 12 dynamic signals and 2 Keyphasorsignals
DynamicRange110 dB @ fs = 102.4 ksps 
Signal/NoiseRatio110 dB @ fs = 102.4 ksps 
A/DConversionSigma-Delta 24 bits nominal 
Bandwidth 0 to 40 kHz 

AQ 4XU/I ST

Servo Amplifier

3300 NSv Reverse Mount Probe

330906-02-12-CC-DD-EE 3/8-24 UNF threads
05 0.5 meter (20 in)
02 Miniature coaxial ClickLocconnector
standard cable
00 Not required

CP 5612 Communications Processor

Power Supply Rack

Overvoltage:28V DC
Input Voltage:400-480V AC, 3-phase (±10%)
Output Voltage:24V DC regulated
Output Current:50A (continuous), 60A (peak)
Power Rating:1.2kW (per module)
Efficiency:>93% (at 50% load)
Power Factor:>0.95

70 AS 47b-E Module

Power Supply: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Number of Channels: 8
Current Output Range: 4-20mA
Voltage Output Range: 0-10V
Resolution: 16-bit
Accuracy: ±0.1% of span
Current: ≤750Ω
Voltage: ≥1kΩ

Diode Module

Input Voltage:24V DC nominal
Input Current:3-8mA per channel 
Isolation:1500V AC (field to logic)
Response Time:<1ms (ON/OFF)
Number of Channels:32 
Voltage Rating:1600V (V_RRM)
Current Rating:300A (I_FAVM)
Surge Current:8kA (I_FSM, 10ms)
Forward Voltage:1.25V @ 300A (typical)

Remote I/O Module

Remote I/O 
with 20 digital inputs and 8digital outputs
Operating temperature 0...+60 °C
for ELOPII Factory programming tool 
20 isolated digital inputs
8 isolated digital outputs
SIL 3/PL e (Cat. 4) safety rating
24 VDC power supply
TTL compatible inputs

Dual-port EtherNet/IP Module

Ethernet Communication Module

Connection method Point-to-point
Connector RJ-45
Transmission method Half-duplex
Transmission speed 10 Mbps
Transmission route 100 ohm twisted-pair cable

Operator Interface

Process Variable Monitor

+/-10 Vdc I/O : -10 Vdc to +10 Vdc
4-20 mA Barrier I/O:4-20 mA DC
Voltage Compliance:13.66 V
Isolation:500 Volts
Power Consumption:7.0 Watts, typical
Accuracy:Within ±0.33% of full-scaletypical, ±1% maximum

Miniature Circuit Breaker

AC: 230/400 V
DC: 60 V
Rated Current (Iₙ): 42 A
Rated Insulation Voltage (Ui): 500 V
Rated Impulse Withstand Voltage (Uimp): 6 kV