ALL MANUFACTURERS

Control Transformer Module

Input Voltage:120V AC ±10%
Output Voltage:24V DC regulated
Power Rating: 100VA (typical)
Efficiency: >85% at full load
Isolation: 1500V AC input-to-output
Thermal Protection: Shutdown at >85°C 

Dual Differential Expansion Monitor

Sensor Input:-24V DC @ 4mA 
Analog Output:4-20mA
Relay Outputs:3 per channel
Communication:RS-485 Modbus RTU (optional)
Measurement Range:±4mm (±0.16 in) standard
Resolution:0.1% of full scale
Frequency Response:DC to 10Hz (-3dB)
Channels:2 fully independent monitoring channels

Dual Accelerometer Monitor

1 5 0-25 mm/s pk 
1 5 0-25 mm/s pk
val Option0 0 Not required 
0 0 None 
Measures Absolute Machine Housing
Provides Two Independent Channels
Provides Over 10,000 High-Pass and Low-Pass Filter Combinations

Dual Vibration XY/GAP Monitor

1 5 0-500 µm pp
0 1 3300 8 mm, 3300 XL 8mm 
or7200 5 mm and 8 mm
0 3 7200 11 mm Proximitor®Sensor(not XL), 100 mV/mil 
0 0 No Relays 
0 0 Not required
0 2 Internal 

Terminal Module

CPU315F-2DP Failsafe Processor Module

Simatic DP Terminating Module ET200S

EPC50 OP Board

Trusted 24V DC Rack Grill Fan

Simple installation and connection.
Capable of moving 69 m3/h (40.6 ft3/min).
24 Vdc operation.
Low noise (32 dB per fan)

1M IETP CORD RJ45/R45

Industrial Ethernet TP Cord 
RJ45/RJ45, CAT 6A
TP cable 4x2
pre-assembledwith 2 RJ45 connectors,
length 1 m

Memory card

SIMATIC S7
memory cards 
for S7-1x 00 CPU
3, 3V Flash, 2 GB

CPU 1513R-1 PN Central Processing Unit

SIMATIC S7-1500R
CPU 1513R-1PN
central processing unit 
withwork memory 300 KB for program and 1.5 MB for data
1st interface:PROFINET RT With 2-port switch
SIMATIC memory card required

Analog Input Module

SIMATIC S7-1500 
AI 4xU/I/RTD/TC ST
16 bit resolution
Accuracy 0.3%
4 channels in groups of 4
2 channels for RTD measurement
Common mode voltage 10 V

PM1507 Power Supply

SIMATIC PM 1507 24 V/3 A 
Stabilized power supply for 
SIMATIC S7-1500 
input:120/230 V AC
output: 24 V DC/3 A

PROFINET IO Device Interface Module

SIMATIC ET 200MP
PROFINET IO device Interface module 
IM 155-5 PN HF, forET 200MP electronic modules 
Up to 12 IO modules without PS
Up to 30 IOmodules with additional PS 
Integrated 2-port switch; RJ45 shared device MRP
IRT >=0.25 ms; Isochronous mode FW update
I&M0...3; Prioritized startup, S2redundancy

Proximitor Seismic Monitor

Signal Accepts from:1 to 4 proximity
velocity or accelerationtransducer signals
Power consumption:7.7 watts, typical
Standard:I/O 10 kΩ
Output Impedance:550 Ω
Transducer Power Supply:-24 Vdc
Voltage Compliance:0 to +12 Vdc range acrossload