Up to 12 Mbps.
Auto-detection of baud rate
Address Range: Configurable from 0 to 126
Supply Voltage: 24 VDC ±10%.
Power Consumption: < 2 W
Operating Temperature: -10°C to +55°C.
Storage Temperature: -40°C to +70°C
Input Voltage: +5V, +12V
Current Consumption: Typically under 2A
RS-232/RS-485
Operating Temperature: 0°C to 50°C.
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 85% (non-condensing)
Typically 24V DC or 12V DC
Output Type Source
Load Voltage 15 30 VDC Maximum
On-State Voltage 24 V (typ), load current @ 0.5A
Off-State Leak Current 5.0 µA (max)
Turn-On/Turn-Off Time 10 ms (max)
Local Bus Power 12 VDC at 300 mA
AmbientTemperature-40°C to +70°C
Shock 10g ½ Sinewave for 11msec
Vibration 1mm Peak to Peak from 2 to 13.2Hz
0.7g from 13.2 to 150Hz
AirborneContaminantsISA-S71.04 –1985 Airborne
Contaminants Class G3
Power Supply: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Number of Channels: 8
Current Output Range: 4-20mA
Voltage Output Range: 0-10V
Resolution: 16-bit
Accuracy: ±0.1% of span
Current: ≤750Ω
Voltage: ≥1kΩ
Input Voltage:24V DC nominal
Input Current:3-8mA per channel
Isolation:1500V AC (field to logic)
Response Time:<1ms (ON/OFF)
Number of Channels:32
Voltage Rating:1600V (V_RRM)
Current Rating:300A (I_FAVM)
Surge Current:8kA (I_FSM, 10ms)
Forward Voltage:1.25V @ 300A (typical)
Product No. : 3805H
Product type : Analog Output Module
Output current range : 4-20 mA output (+6% overrange)
Points : 8 output
Current Loop, DC Coupled
Type : TMR, AO
Resolution : 12 bits
Output Accuracy : <0.25% (in range of 4-20 mA) of FSR (0-21.2 mA), from 32° to 140° F (0° to 60° C)
Range: Typically 4-20 mA
Input Impedance:≤ 10 Ω
Load Capacity: Standard 0-500 Ω
Voltage: 24 V DC
Test Voltage: Typically 1.5 kV AC
Typical: ±0.1% of full scale
Voltage: 125 VDC Nominal
Power Consumption: Typically < 5W
Input-to-Input: 1500 VAC min.
Input-to-Output/Logic: 1500 VAC min.
Output-to-Output: 500 VAC min.
Output/Logic-to-S+ I/O: 500 VAC min
Rated Voltage:400 V AC (3-phase, 4-wire)
Rated Current:22 A (continuous)
Rated Frequency:50/60 Hz
Transfer Time:< 100 ms (typical for open transition)
Withstand Current:10 kA (IEC 60947-6-1)
Mechanical Life:10,000 cycles (minimum)
Number of Positions:10 Position
Pitch:9.53 mm
Current Rating:30 A
Voltage Rating:300 V
Wire Gauge Min:22 AWG
Wire Gauge Max:14 AWG
Type:Terminal Block
Number of Rows: 2 Row
Mounting Style:Panel Mount
Protocol: PROFIBUS DP-V0
Data Transfer Rates:up to 12 Mbp
Connector Type: 9-pin D-sub
Electrical Interface: RS-485
Voltage: +5 V DC
Power Consumption: 1-2 W
Max. Input Data (to Master): Up to 244 bytes per cycle
Max. Output Data (from Master): Up to 244 bytes per cycle
Protocol: PROFIBUS DP-V0 Data Transfer Rates:up to 12 Mbp Connector Type: 9-pin D-sub Electrical Interface: RS-485 Voltage: +5 V DC Power Consumption: 1-2 W Max. Input Data (to Master): Up to 244 bytes per cycle Max. Output Data (from Master): Up to 244 bytes per cycle
CPU Type: 32-bit RISC-based processor
Clock Speed: 100–200 MHz
Program Memory: Up to 4 MB Flash
Data Memory: Up to 2 MB RAM
Execution Speed: 0.1 ms
Input Voltage: 24V DC
Resolution: 12-bit to 16-bit
Channels:8/16 DI or DO
Input Voltage:24V DC
Output Type:Relay/Transistor
Isolation:1.5kV AC
PROFIBUS DP (via coupler)
Modbus RTU (RS-485)
EtherNet/IP (optional)
Collector-Emitter Voltage (Vces):1200V
Collector Current (Ic @ 25°C):450A
Collector Current (Ic @ 80°C):300A
Pulse Current (Icm):900A
Power Dissipation (Ptot):1800W
Gate-Emitter Voltage (Vges):±20V
Turn-on Delay Time (tdon):110ns
Rise Time (tr):50ns
Turn-off Delay Time (tdoff):400ns
Fall Time (tf):120ns
Switching Frequency:Up to 20kHz
Supply Voltage: 24V DC (19.2-30V DC)
Power Consumption: 1.5W
Current Capacity: 6A
Isolation Voltage: 500V AC
Fieldbus Protocol:PROFIBUS DP-V1
Data Rate:Up to 12 Mbps
Address Range:1-125 (PROFIBUS)
I/O Connection:S800 I/O bus
Microprocessor-based protection
Three-phase trip-free mechanism
Front-connected auxiliary contacts
Integrated earth fault protection
Remote control and monitoring capabilities
High-performance AC800F platform
Supports a wide range of I/O modules
Supports a variety of programming languages
Suitable for a wide range of industrial applications
Compact and modular design
Voltage Input: 380V to 690V AC (3-phase)
Switching Frequency: 2–16 kHz range
Operating Temperature: -10°C to +50°C (ambient, typical)
Humidity: ≤95% non-condensing
Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs
Memory:32MB SDRAM
Control Loop Time:100μs (speed)
Digital I/O:12x 24V DC inputs
Supply Voltage:24V DC ±10%
Power Consumption:15W max
Isolation:2500V AC
RM (Redundancy Module) to support
C200 redundancy
Input Power Supply 24V DC (nominal)
Operating Temperature:-10°C to 60°C (14°F to 140°F)
Storage Temperature:-40°C to 85°C (-40°F to 185°F)
Humidity Tolerance:5% to 95% non-condensing
