Power Rating: 11 kW
Current Rating: 27 A
Input Voltage: 380–480 V AC, 3-phase
Output Frequency: 0-550 Hz
Overload Capacity: 150% for 1 minute
Enclosure Rating: IP20 / UL open class (NEMA 1)
Process Temperature Range:
-40°C to +150°C (-40°F to +302°F)
Process Pressure Range:
-1 to +40 bar (-100 to +4000 kPa)
Output Signal: 4…20 mA/HART
Power Supply: 14…36 V DC
Protection Rating: IP66/IP68 (0.2 bar)
Wetted Materials: Stainless Steel (1.4435)
Probe Length: Up to 9,000 mm
Rated insulation voltage AC 800 V
Rated impulse voltage/pollution degree 8 kV/3
Nominal system voltage Un AC, 3/(N)AC 0…793 V
Supply voltage USAC 88…264 V
Frequency range US 42…460 Hz
Supply voltage US DC 77…286 V
Frequency range US 42…460 Hz
Sensor: CMOS
Resolution: 26 Megapixels
Pixel Size: Typically 3.45 µm
Operating Temperature: -10°C to +50°C
Storage Temperature: -20°C to +60°C
Power Supply: 12V DC
Product or component type:Communication module
Product compatibility:Lexium 32M
Accessory / separate part destination:Servo drive
Number of addresses:256
Electrical connection:2 connectors RJ45
4 LEDs (green/red) for communication status
Range compatibility:PacDrive 3
Device short name:SH3.....P
Product or component type:Servo motor
Maximum mechanical speed:8000 rpm
rated supply voltage:115...480 V
Network number of phases:Three phase
Continuous stall torque:1.25 N.m at 115...480 V three phase
Continuous power:690 W
Maximum current Irms:5.7 A
Maximum mechanical speed 8000 rpm
rated supply voltage 115...480 V
Continuous stall current 2.9 A
Continuous power 1130 W
Speed feedback resolution 128 periods
Torque constant 0.7 N.m/A at 120 °C
Back emf constant 48 V/krpm at 20 °C
Maximum axial force Fa 80 N
Acceleration Range: ±2g, ±5g, ±10g, or ±50g
Voltage output, typically 0-5V or 0-10V
Supply Voltage: 5V DC or 12V DC
Operating Temperature: -40°C to +85°C
Universal Input Output IOTA
Input Channels 1 16 Channels
Common Mode Voltage, dc to 60 Hz -6 to +5 V peak
A/D Converter Resolution 16 bits
Normal Mode Rejection Ratio, at 60 Hz 19 dB
Normal Mode Filter Response Single-pole RC, -3 dB @ 6.5 Hz
Input Impedance (voltage inputs) > 10 M Ω powered
Input Scan Rate 50 ms
Supports fiber-optic medium
NFPA Class B or Class A operation
Data is immune to all environmental noise
Optical isolation prevents ground loops
High-Speed NFN fiber-optic medium
Fiber type: 62.5/125 micrometers (multi-mode);
50/125 micrometers (multimode),
or 9/125 micrometers (single mode)
Maximum attenuation: 10 dB with 62.5/125 μm cable, 6
Module Type:Central Processing Unit
Number of Slots:1 (Single slot)
Battery-backed memory: 1 Mbyte
Number of Points:12K discrete inputs and outputs
Serial Ports:1 (RS422/485 compatible)
Current Required:3.3 Amps nominal
8-Wide I/O
Interface Carrier
with Carrier Shield Bar
Operating temperature-40 to 70°C (-40 to 158°F)
Storage temperature-40 to 85°C (-40 to 185°F)
Relative humidity5 to 95%, non-condensing
3300 XL 8 mm Probe
M10 x 1 thread
with armor
10 1.0 meter (3.3 feet)
01Miniature coaxial ClickLocconnector
with connectorprotector, standard cable
00 Not required
For use in Tight
Installation Requirements
Replaces 3300 RAM Transducer Systems
and 3000-Series or 7000-Series 190 Transducer System
Average Scale Factor of 7.87 V/mm (200 mV/mil)
For use in Tight
Installation Requirements
Replaces 3300 RAM Transducer Systems
and 3000-Series or 7000-Series 190 Transducer System
Average Scale Factor of 7.87 V/mm (200 mV/mil)
Device short name:BMH
Maximum mechanical speed:8000 rpm
Range compatibility:Lexium 32
rated supply voltage:240 V
Continuous stall current:5.55 A
Continuous power:1.68 W
Maximum permanent current:17.84 A
Holding torque:3 N.m holding brake
Torque constant:0.61 N.m/A at 120 °C
Back emf constant:39.3 V/krpm at 120 °C
Range Compatibility:PacDrive 3
Maximum mechanical speed:9000 rpm
Continuous stall current:0.73 A
Continuous power:290 W
Maximum current Irms:2.9 A
Speed feedback resolution:128 periods
Torque constant:0.58 N.m/A 248 °F (120 °C)
Back emf constant:40 V/krpm 68 °F (20 °C)
Power Supply:24VDC
No. of Inputs:(10) 24V dc; (4) fast 24V dc
Input Circuit Type:24 VDC
Output Circuit Type Relay; FET
Relay Contact Rating:24-125VDC; 120-240VAC
Power Supply Usage:82 VA
Input Power:24V DC
Inputs:(10) 24V DC and (4) Fast 24V DC
Type:FT color
Diagonal:10.4" (264 mm)
Resolution:VGA, 640 x 480 pixels
Buffer time:10 min
Variant:Lithium ion
Clock frequency:266 MHz
L1 cache:16 kB
Flash:2 MB (for firmware)
Cooling:Passive via heat sink
Mode/Node switches:2, 16 positions each
Accuracy At 25°C: Typ. 10 ppm (1 second) per day
Controller:SMC
Range of measurement: from 100N to 2kN
Accuracy class: 0.5%
Corrosion resistant
STRAIN AND FORCE SENSOR
TR FORCE TRANSDUCER FOR
MEASURING SPINDLES TENSION
Range Compatibility PacDrive 3
Device short name SH3.....P
Maximum mechanical speed 8000 rpm
rated supply voltage 115...480 V
Continuous stall current 1.8 A
Continuous power 690 W
Maximum current Irms 5.7 A
Speed feedback resolution 128 periods
Series Type:Low-inertia
Voltage Class:400 Volts AC
Frame Size:63 millimeters
Magnetic Stack Length:3 inches
Rated Speed:7000 rpm
Feedback:Multi-turn high-resolution encoder
Shaft Key/Seal:Shaft key/no shaft seal
Brake:24 Volts DC brake
Connector DIN 41612, type F, 48 pin
Supply voltage 24 VDC nominal
Voltage range 20 . . . 32 VDC
Current approx. 200 mA
Reference voltages ± 15 V (± 5 %) Ø 50 mA
Current 0 . . . + 20 mA
Current + 4 . . . + 20 mA
Output voltage 24 V PWM for the solenoid
Dither frequency 100 Hz, 150 Hz, 250 Hz
GENERATOR CONTROLLER
ANALOG INPUT: 0-5 VDC OR 4-20 MA DC
DISCRETE INPUTS (16):
5 MA EACH WHEN CLOSED TO SWITCH COMMON
(TERMINAL 65)
MAXIMUM 80 MA TOTAL
POTENTIAL TRANSFORMER INPUT: 150 VAC MAX
AC: 100-240V AC
Frequency: 50/60 Hz
Output Voltage: 24V DC
Output Current:10-15A
Operating Temperature Range:-20°C to 70°C
Storage Temperature Range:-40°C to 85°C
Conductivity range: 0.001 μS/cm to 2000 mS/cm
Temperature range: -10°C to 110°C (14°F to 230°F)
Analog output: 4-20 mA
Input voltage: 24 V DC
Power consumption: 15 W
Operating Temperature: -10°C to 60°C (14°F to 140°F)
Storage Temperature: -20°C to 70°C (-4°F to 158°F)
Input Range: 0-10V (voltage),
4-20mA (current)
Resolution: 16-bit
Sampling Rate: 1000 samples per second per channel
Accuracy: ±0.1% of full scale
Isolation: 1500V isolation between channels and the system
Operating Temperature Range: -20°C to +60°C
Storage Temperature Range: -40°C to +85°C
Power Supply Voltage: 24V DC
Power Consumption: Maximum 5W
CE-compliant, not conformally coated
Redundancy not supported
Input Channels: 8
Input Scan Rate: 32 samples per second
Available Input Types:
Rectangular
Sine Wave
Series:POINT I/O
Module Type:Digital Contact Module
Series:POINT I/O
Outputs:4 N.O relay
Product Description Four (4) channel Relay output module
POINTBus Current 80 milliamps
No. of outputs Four (4) Normally Open (N.O.) contact outputs
Power Dissipation, Max;0.5 Watts
Output delay time, on to off, max:26 ms
Thermal Dissipation:1.7 BTU/hour
Contact resistance, initial:30 m
Thermal Dissipation:10 BTU/hour
Isolation Voltage:50 Volts Continuous
Inrush Current 6 amps for 10 milliseconds
Overvoltage Protection:Reverse Polarity
Power Supply Current:10 amps
Power Consumption:9.8 Watts
Field Power:24 Volts DC
Module Type;Expansion Power Supply
Series:POINT I/O
4-20 mA current loops
0-5 V or 0-10 V DC voltage signals
Operating Temperature Range: -30°C to +65°C
Storage Temperature Range: -40°C to +85°C
Humidity: 5% to 95% RH, non-condensing
Series: Mark VIe
Simplex Primary Turbine Protection Input Terminal Board
Number of inputs: 4
Number of outputs: 2
MPU pulse rate range: 2 Hz to 20 kHz
Contact voltage sensing: 20 V dc
Technology: Surface mount
Temperature: -30 to +65C
Series:RX3i PacSystem
Part Number:IC695CPE305CA IC695CPE305CA-BCAD
Compatibility:PACSystems RX3i
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Maximum Block Size:128 kilobytes
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Floating Point:Yes
Serial Communication:RS-232
Ethernet Port:Yes
Part Number IC695ETM001
Specialty ModuleRX3i Ethernet module
10/100 Mbits 2 RJ45 connections one IP
address occupies one slot on system base
Current Consumption
840 mA @ 3.3 VDC; 614 mA @ 5 VDC
Operational NotesUniversal Backplane Only.
Uses PCI Bus. Client/Server
Number of Channels: 8 digital output channels
Output Voltage Range: 24 VDC ± 20%
Output Current: Maximum 1 A per channel
Power Supply Voltage: 24 VDC
Communication Interface:
Dual RBUS for high-speed data transfer
Power Supply Voltage:
10 to 28.8 VDC from SPBus
Operational Temperature Range: -15°C to +70°C
Storage Temperature Range: -25°C to +70°C
Relative Humidity: Up to 98%
Number of channels: 32 current inputs
Current input: 0-20 mA (input resistor 220 ohm)
Current accuracy: +/- 0.2% of full scale
(resistor accuracy = 0.1%)
Current input lter: RC = 33 µs
Digital resolution: 12 bits
Connectors: screw terminals, 2.5 mm
Input voltage: 24 VDC ±20%
Power consumption: maximum 20 W
Connectors: screw terminals, 1.5 mm
operational: 0° C to 70° C
storage: -25° C to 70° C
Power supply voltage: 10 to 28.8 VDC
SPBus connector: 9-pin male DSUB
Input voltage: 24 VDC ±20%
Power consumption: maximum 20 W
Connectors: screw terminals, 1.5 mm
operational: 0° C to 70° C
storage: -25° C to 70° C
Power supply voltage: 10 to 28.8 VDC
SPBus connector: 9-pin male DSUB
Input supply voltage: 24 VDC(+30%, -25%)
Nominal current consumption: ≈ 0.8 A
Start-up current: Max. 2.7 A
Power consumption: Max. 20 W
Heat dissipation: Max. 20 W
