ALL MANUFACTURERS

Control Memory Xchange Module

Data Transmission Rate: 2.12 Gbaud
Reflective Memory Capacity: 16 MB SDRAM
Access Time: 200 to 400 nanoseconds
Node Capacity: Supports up to 256 nodes in a network
Connectors: Fiber optic LC type, conforming to IEC 61754-20
Operating Voltage: +5 VDC (from power supply)
Current Requirements: 1.8 Amperes

Field Exciter Power Module

Input Voltage: 500 VAC or 420 VDC
Current Rating: 50 A
Frequency Compatibility: 50/60 Hz
Output Control Mode: Pulse Width Modulation (PWM)
Operating Temperature Range: -20°C to +70°C
Protection Rating: IP20

SmartGuard 600 controller

DeviceNet Voltage Range:11 to 25 Volts DC
Current Consumption:230 milliamps at 24 Volts DC
Voltage, On-State Input max.:11 Volts DC
Voltage, Off-State Input max.:5 Volts DC
Input Current:4.5 milliamps
Test Output Type:Current Sourcing
Pulse Test Output Current:0.7 Amps
Output Current:0.5 Amps
Output Surge Current:0.5 Amps

Master-Modul

SIMATIC DP
Master-Modul IM 180 für 
PROFIBUS-DP,max
12 MBaud
Nennwert (DC):5 V
Stromaufnahme, typ. :250 mA
Prozessortyp:80C165 (40 MHz)
Art des Speichers:2x 128 kbyte
Schnittstellen/Bustyp:Dual-Port-RAM

Proximity Sensor

2 or 4 mm measurement range
−40 to 180 °C operating temperature
0.5, 1.0, 1.5, 2.0 or 5.0 m integral coaxial cable
Versions certified for use in potentially explosive atmospheres
Conforms to API 670 5th edition
8 mV/µm or 2.5 µA/µm (2 mm range)
4 mV/µm or 1.25 µA/µm (4 mm range)
−40 to 180 °C, Ø8.2 mm tip, reverse-mount

Signal Conditioner

Voltage at min. GAP : −1.6 V
Voltage at max. GAP : −17.6 V
Dynamic range : 16 V
Output impedance : 500 Ω
Short-circuit current : 45 mA
Output capacitance : 1 nF
Output inductance : 100 µH
Operating : −35 to +85°C
Storage : −40 to +85°C

Emergency Turbine Protection I/O Pack

Input Voltage Range: 85–264 V AC
Output Voltage: 24 V DC
Output Current: 10 A
Efficiency: 88%
Operating Temperature Range: -40°C to +70°C
Storage Temperature Range: -40°C to +85°C
Humidity Range: 5% to 95% non-condensing
Power Consumption: Approximately 25 W

Communication Board

VM600 series
Humidity: 5% to 95% non-condensing
Vibration: 0.15 g²/Hz (5 to 500 Hz)
Shock: 15 g (11 ms half-sine)
Operating Temperature Range: -20°C to +60°C (-4°F to +140°F)
Storage Temperature Range: -40°C to +85°C (-40°F to +185°F)

CPUM modular CPU card

VM600 series
Humidity: 5% to 95% non-condensing
Vibration: 0.15 g²/Hz (5 to 500 Hz)
Shock: 15 g (11 ms half-sine)
Operating Temperature Range: -20°C to +60°C (-4°F to +140°F)
Storage Temperature Range: -40°C to +85°C (-40°F to +185°F)

PROPORTIONAL AMPLIFIER CARD

PROPORTIONAL AMPLIFIER CARD
2.5AMP
12VDC
VP01-B

OPERATOR INTERFACE

OPERATOR INTERFACE
TOUCHPANEL
5.7 INCH MONOCHROME LCD
24 VDC
0.6 AMP
RS-232 / RS-485 / RS-422 / PC/PRINTER

Process Variable Monitor

6-channel monitor
Parameters include:
Pressures
Flows
Temperatures
Levels
Accepts 4 to 20 mA current inputs
Front panel LEDs: OK, TX/RX, Bypass

Process Variable Monitor

(6) Channel Monitors
Current Inputs: +4 to +20 mA
Voltage Inputs: -10 Vdc and +10 Vdc
Provide Essential Machine Information
Accepts 4 to 20 mA current inputs
Front panel LEDs: OK, TX/RX, Bypass

PROTECTION RELAY

Ambient Humidity Maximum:Up to 95% non condensing
Dimensions:approx: 11.5 in H x 5.5 in W x 8.5 in L
Display Version:Enhanced
Fuse:3.15 A H 250 V
Input Power:110-250VDC 100-240VAC
Manufacturer:GE Multilin
Model Number:369-HI-R-M-0-0-0-E
Phase Current Input:1 A and 5 A secondary

Analog Output Module

Output Type:4-20 mA 
Output Channels:16
Output Temperature Drift:0.005% of Full Scale/°C
Output Readback Accuracy:±4% of Full Scale
Resolution:± 0.05% of Full Scale
Directly Settable Output Current Range:0 mA, 2.9 mA to 21.1 mA
Maximum Resistive Load:800 ohms
Maximum Open Circuit Voltage:22 V

Bus Connection Module

Auxiliary power supply Powered from host device (5V dc)
Burden ~ 0.4 W Max
Max data transfer rate 1.25 Mbps
Operating temperature range -10...55°C
Storage temperature range -40...70°C

Power interface board

Application: DCS800 DC Drives
Operating Temperature:0°C to +55°C
Storage Temperature:-25°C to +70°C
Humidity:Up to 95%, non-condensing

Reflective Memory interface Module

Memory Size:8 MB, 16 MB, or 32 MB
Data Transfer Rate:Up to 43 MB/s
Node Support:Supports up to 256 nodes
Connectors:
ST-style fiber-optic connectors
Power Requirements:+5 VDC
Storage Temperature:-40°C to +85°C
Operating Temperature:0°C to +60°C

Data Acquisition Interface Unit

8 Signal Inputs
Enhanced Parallel Port for 
Connecting to 208-P DAIUs
80 Mb Hard Disk Space
Up to 16 Channels
Real-Time Display Capability
Backwards Compatible with 
Existing ADRE 3 Databases

Extension Cable

Impedance: Typically 50Ω or 75Ω
Length: 45 feet (13.72 meters)
Temperature Range:
Operating: -40°C to +120°C.

Isolated current input module

Input Type:4-20 mA
Input Voltage:24 V DC
Input Range:4-20 mA
Signal Isolation:1500 V to 2500 V
Accuracy:accuracy of ±0.1%
Operating Temperature Range:0°C to 60°C (32°F to 140°F)
Power Supply:24 V DC

AC-DC/DC-DC Power supply Converter Moudle

Range: 85 V to 264 V AC
Frequency: 50/60 Hz 
Primary DC Output Voltage: 24 V DC
Total Output Power: 160 W
Primary Output Current: 6.7 A
Storage Temperature: -20°C to 85°C
Operating Temperature: 0°C to 60°C

Synchron Transformer

Rated Power: 5 VA (Volt-Ampere)
Primary Voltage: 110 V (Volts)
Secondary Voltage: 9 V (Volts)
Rated Power Capacity: 5 VA 
Frequency: 50/60 Hz

Synchron Transformer

Rated Power: 10 MVA
Primary Voltage: 7 kV
Secondary Voltage: 0 kV 
Frequency: 50 Hz or 60 Hz 

Rigi Crowbar Drive PCB

Power Supply:24V
Operating Temperature Range
Typically -20°C to +60°C
Storage Temperature Range
-40°C to +85°C

Interface Board

24 VDC
Low power design
typically <10 W
Multiple I/O ports for 
interfacing with sensors
actuators, and controllers.
Optimized for high-speed 
communication to minimize latency

Prog.Logic Controller

Memory Size:642 kB
Memory Type User Data:RAM
Controller Processing Time:0.00008 ms
Analog Inputs:2
Analog Outputs:1
Number of Digital Inputs:6
Number of Digital Outputs:6
Number of Digital Configurable I/Os:0
Input Voltage Type:DC
Rated Voltage (Ur):24 V DC
Supply Voltage:20.4 … 28.8 V DC

3-phase Contactor

Type: 3-phase contactor
Rated Operational Voltage (Ue): 690 V AC
Control Circuit Voltage: 100-250 V AC/DC
Rated Current: 10 A
Rated Insulation Voltage (Ui):1000 V AC
Operating Temperature:-40°C to +70°C
Storage Temperature:-40°C to +80°C

Processor Module

PM564RPETH
1SAP121000R0001 
2AMP
120-240VAC
24VDC
4W

Current measurement scaling board

Function: 4-20 mA
Input impedance: Typically 250 Ω
Accuracy: ±0.5% of full scale 
Voltage supply : Typically +24V DC (±10%)
Operating Temperature Range: Typically -20°C to +60°C.
Storage Temperature Range: Typically -40°C to +85°C

3300 XL NSv Proximity Transducer

3300 NSv Probe
M10X1 thread, witharmor
10 1.0 meter (39 in
01Miniature coaxial ClickLoc connectorwith 
connector protector, standardcable
05 Multiple Approvals

Safety Controller Module

Microprocessor: 1066 MHz Intel EP80579
Operating System: QNX Neutrino
Operating voltage: 24 VDC
Operating Temperature: -10°C to +60°C.
Storage Temperature: -40°C to +85°C
Memory:4GB to 16GB RAM
Modbus TCP/IP, Profibus DP

UCSB Controller Module

Operating voltage: 24 VDC
Operating Temperature: -10°C to +60°C.
Storage Temperature: -40°C to +85°C
Memory:4GB to 16GB RAM
Modbus TCP/IP, Profibus DP

UCSB Controller Module

Operating voltage: 24 VDC
Operating Temperature: -10°C to +60°C.
Storage Temperature: -40°C to +85°C
Memory:4GB to 16GB RAM
Modbus TCP/IP, Profibus DP

Safety Controller Module

Number of channels: 24
Power supply voltage: 28 V dc
Analog output current: 0-20 mA
ControlST Software Suite Version: V06.01
Voltage Range: 14 to 32 V dc
Outputs: 24 V dc
Mounting: DIN-rail mounting
Technology: Surface mount
Operating temperature: -30 to 65°C

Mark VIe controller

Processor:1066 MHz EP80579 Intel Processor
Operating Voltage:Variable
Input Channels:2 Hall Effect Pulse Inputs, 2 Analog Inputs
Output Channels:4 Digital Input/Output Channels
Certifications:CE, RoHS Compliant

Mark VIe controller

Processor:1066 MHz EP80579 Intel Processor
Operating Voltage:Variable
Input Channels:2 Hall Effect Pulse Inputs, 2 Analog Inputs
Output Channels:4 Digital Input/Output Channels
Certifications:CE, RoHS Compliant

High-Speed Industrial Control Module

Processor:1066 MHz EP80579 Intel Processor
Operating Voltage:Variable
Input Channels:2 Hall Effect Pulse Inputs, 2 Analog Inputs
Output Channels:4 Digital Input/Output Channels
Certifications:CE, RoHS Compliant

Quad Core Controller

Mark VIe Controller
Altitude for Normal Operation :
0-1000 m at 101.3 to 89.9 kPa
Memory Type:
2 GB DDR3-1066 SDRAM
with error correcting code

CPU Ccontrol I/O Board

Digital Inputs: 24V DC
Analog Inputs: 4-20mA or 0-10V
Power Supply:24V DC
Operating Temperature Range:0°C to +60°C

I/O Control Module

Digital Inputs: 24V DC
Analog Inputs: 4-20mA or 0-10V
Power Supply:24V DC
Operating Temperature Range:0°C to +60°C

CHARGING CONTROL BOARD

Input Voltage:380-480V
Charging Voltage Range:12V to 600V DC
Current Rating:10A to 100A
Operating Temperature Range:-10°C to +60°C
Storage Temperature:-20°C to +70°C

Quad Elephant Inverter Rectifier Power Board

DC Output:DC 500-800V
Current Rating:100A to 200A 
Continuous Current Rating:150A
Switching Frequency:10-20 kHz
Storage Temperature:-20°C to +70°C
Operating Temperature Range:-10°C to +55°C

Programmable Logic Controller

Memory Size:642 kB
Memory Type User Data:RAM
Controller Processing Time:0.00008 ms
Analog Inputs:2
Analog Outputs:1
Number of Digital Inputs:6
Number of Digital Outputs:6
Number of Digital Configurable I/Os:0
Input Voltage Type:DC
Rated Voltage (Ur):24 V DC
Supply Voltage:20.4 … 28.8 V DC

KONE Elevator Pulse Encoder Interface Module

Power Supply: Typically 24 V DC
Max Input Frequency: Typically 100 kH
Input Voltage Level: Usually 5V or 24V
Operating Voltage Range: 18-30V DC
Operating Temperature: -10°C to +55°C 
Storage Temperature: -20°C to +70°C

ANALOG IO EXTENSION

Supply Voltage:
Typically 24V DC or 48V DC
Voltage: 0-10 V, ±10 V, 0-5 V.
Current: 4-20 mA
Operating Temperature: Typically -10°C to +55°C
Storage Temperature: Around -40°C to +70°C

Interface Board

Supply Voltage:Likely 24V DC or 48V DC 
Current Consumption:150 mA to 500 mA
Operating Temperature:  -10°C to +55°C
Storage Temperature: -40°C to +70°C

Control Panel 10.4

Memory Size User Data:256 MB
Memory Size User Program:256 MB
Memory Type User Data:Flash Disk
Memory Type User Program:DDR RAM
Power Consumption (@Pcons):24 W
Power Supply:24 (18 ... 30) V DC
Product Main Type:CP651
Product Name:Control Panels
Operation 0 ... +50 °C
Storage -20 ... +70 °C

Control Panel 5.7 TFT touch screen

Memory Size User Data:128 MB
Memory Size User Program:256 MB
Memory Type User Data:Flash Disk
Memory Type User Program:DDR RAM
Power Consumption (@Pcons):16.8 W
Power Supply:24 (18 ... 30) V DC
Product Main Type:CP630
Product Name:Control Panels