ALL MANUFACTURERS

Digital Remote Real-Time Network (RTN) Module

Digital Output 2DO 24VDC 2A - 5 Pack

ELECTRONIC MODULE

SIMATIC DP
ELECTRONIC MODULE FOR ET 200S
2 AISTANDARD 15 MM WIDE +/-10 V
13 BIT + SIGN +/-5 V; 12 BIT+SIGN
1..5V; 12BIT
CYCLE TIME 65 MS/CHANNEL 
WITH LED SF(GROUP FAULT)

PCB CIRCUIT BOARD

Analog Outputs: 4–20 mA
Voltage: 12–24 V DC
Consumption: ≤5 W 
Drive Coil Excitation: 10–50 V AC
Standard: -40°C to +70°C (-40°F to +158°F)
Humidity: 0–95% RH (non-condensing)

KTP400 Basic Mono Panel - 3.8 Inch

Communication Module

Order Code:3BHE019958R0101
Functional Designation:UA D206 A
Power Supply:5 V DC
Consumption: 500 mA (max)
Data Rate:300 bps – 115.2 kbps (per port)
Isolation:500 V AC 

Interface Module

Signal Channels:16 single-ended analog inputs
 Voltage: ±10V, ±5V, ±1V, 0–10V
Current: 4–20mA, 0–20mA 
Resolution:16-bit (including sign bit)
Accuracy:±0.05% of full scale (25°C)
Sampling Rate:10 ms/channel 
Input Impedance:>1 MΩ
Overvoltage Protection:±30V continuous
Common-Mode Rejection:>120 dB at 50/60 Hz

Control Board

Clock Speed 800 MHz
Memory:128 MB NOR Flash 
Backplane Interface:PCI-104
Power Requirements:5V DC @ 3.5A
Vibration: 5g @ 10–500Hz

Millmate Controller

Processor: 1.2 GHz 
Power Supply: 24V DC ±10%
Power Consumption: 120W
MTBF: >200,000 hours
Control Loop Speed: 0.5–5 ms (configurable)
Max I/O Points: 5,000 digital / 2,000 analog

Communication Module

Supply Voltage: 5V DC
Power Consumption: 1.2A @ 5V DC (6W)
2× RS-485 ports (9-pin D-sub male).
Baud Rate: 9.6 kbps to 12 Mbps (auto-detect)
Max Stations: 125 slaves per segment
Redundancy Switchover: < 100 ms

Circuit Board

Voltage: 24V DC
Input Impedance: 3 kΩ
Current: 0–20 mA, 4–20 mA
Resolution: 12-bit
Isolation Voltage: 2 kV AC
Altitude: ≤ 2000 m

Analog Input Module

Function:16 AI: U, I, RTD, DI
Number of Analog Configurable I/Os:0
Analog Inputs:16
Input Signal:U, I, RTD, DI
Resolution:Analog Input 13 bit
Degree of Protection:Housing IP20
Supply Voltage:24 V DC
Ambient Air Temperature:
Operation 0 ... +60 °C
Storage -40 ... +70 °C

Robot spray accessory controller

Supply Voltage: 24V DC (±10%), 5A max.
Atomization air pressure control
Fluid flow regulation (via PWM or analog valve)
HV electrostatic control (up to 100 kV)
Solvent purge management
Diagnostic monitoring (clogs, pressure faults)
Power Consumption: 120W (peak)

SIPART PS2 Controllers for Electric Actuator

Panel unit

Module Slots: 8 slots for S800 I/O modules
Orientation: Vertical
Bottom/top gland openings 
(M20/M25 cable glands)
Knockouts for field wiring

Binary In/Out Module

Input Impedance:  3-5 kΩ (High Range)
Maximum Continuous Voltage: 300V DC.
Maximum Surge Voltage: 1 kV, 1.2/50 µs waveform.
Operating Time: < 5 ms.
Release Time: < 5 ms.