ALL MANUFACTURERS

ACS800 Drive Board

Input Voltage:380–480 V AC (±10%)
DC Link Voltage:540–650 V DC
Protections:DC over/undervoltage
Auxiliary Voltage:24 V DC 
Isolation Voltage:2.5 kV AC

INTERFACE BOARD

Data Rates:9.6 kbps – 12 Mbps
Power Supply:24 V DC
Power Consumption:≤ 2.5 W
Isolation:500 V AC
Function:PROFIBUS DP-V1 Slave Interface

Processor module

Memory Size:5032 kB
Memory Type User Data:RAM
Controller Processing Time:0.00002 ms
Number of Digital Inputs:12
Number of Digital Outputs:8
Number of Digital Configurable I/Os:2
Input Voltage Type:DC
Output Voltage (Uout):24 V DC
Output Current:0.5 A
Degree of Protection:IP20
Rated Voltage (Ur):24 V DC
Supply Voltage:20.4 … 28.8 V DC

AC Drive - 15 Hp

Vibration Monitors

DC Input :18~36 Vdc, max 7.5 W
Scale Factorrange:5 to 1000 mV/g
Full scale range: 2 to 80 g peak
Current SinkSource:3.3 mA ± 5%
Open CircuitVoltage:-21 to -24 Vdc
ConfigurableBandpass filter:0.2 Hz to 20 kHz
Supply Voltage :-22.8 to –25.2 Vdc
Maximum RatedCurrent:15 mA

MP-Series 15 m Length Feedback Cable

330103 3300 XL 8 mm Probe

330103 3300 XL 8 mm Probe
M10 x 1 thread,without armor
Example: 0 6 = 60 mm
Maximum case length: 250 mm
10 1.0 meter (3.3 feet)
02 Miniature coaxial ClickLocconnector
standard cable
00 Not required

Rack Interface I/O Module

RIM I/O Module with Modem Interface
Voltage: 24V DC (±10%)
Consumption: ≤15W
Analog Inputs:4–20mA
Digital Inputs:24V DC dry contact
RS-485:Modbus RTU @ 115.2kbps max

TRANSDUCER

0 1 ¼-28 UNF integral stud
0 5Multiple approvals (CSA, ATEX, IECEx,)
Sensitivity 2.5 mV/m/s2 (25 mV/g) ±5%.
AmplitudeLinearity ±1% to 735 m/s2 (75 g) peak.
TransverseSensitivity Less than 5% of axial.
Amplitude ofResonantPeak20 dB maximum

Interconnect Cable

Shielding:100% foil/braid shielding
Impedance: 50Ω ±10%
Max Signal Frequency: Up to 20 kHz 
Operating Range: –55°C to +250°C
Flexibility: 500+ flex cycles
Bend Radius: 8x cable diameter 

MAIN CIRCUIT INTERFACE BOARD

Input Voltage:200–480 V AC
DC Link Voltage:280–650 V DC 
Auxiliary Voltage 24 V DC
PWR (Green): 24V OK
RDY (Yellow): Drive ready
ERR (Red): Fault detected
Isolation Voltage:2.5 kV AC

IGBT Module

Voltage Rating:1200 V
Current Rating:900 A
Technology:Trench-gate IGBT4 
Collector-Emitter Sat.:VCE(sat): 1.75 V (typ.) 
Short-Circuit Withstand:10 μs 
Isolation Voltage:4.5 kV RMS

Sipart DR22 Process Controller - 24 Vdc

IGCT Module

Configuration:Single IGCT
Voltage Rating:4500 V
Current Rating:1200 A 
Critical dv/dt:1000 V/μs (min.)
Isolation Voltage:10 kV RMS
Mounting Force:35–45 kN

Operator Interface Panel

Control Transformer Module

Input Voltage:120V AC ±10%
Output Voltage:24V DC regulated
Power Rating: 100VA (typical)
Efficiency: >85% at full load
Isolation: 1500V AC input-to-output
Thermal Protection: Shutdown at >85°C 

Dual Differential Expansion Monitor

Sensor Input:-24V DC @ 4mA 
Analog Output:4-20mA
Relay Outputs:3 per channel
Communication:RS-485 Modbus RTU (optional)
Measurement Range:±4mm (±0.16 in) standard
Resolution:0.1% of full scale
Frequency Response:DC to 10Hz (-3dB)
Channels:2 fully independent monitoring channels

Dual Accelerometer Monitor

1 5 0-25 mm/s pk 
1 5 0-25 mm/s pk
val Option0 0 Not required 
0 0 None 
Measures Absolute Machine Housing
Provides Two Independent Channels
Provides Over 10,000 High-Pass and Low-Pass Filter Combinations