ALL MANUFACTURERS

Analog Input Module

Model: PFSK110
Part Number: YM322001-EP
Voltage: 24 V DC (±10%)
Power Consumption: ≤3 W
Voltage: 0–10 V, ±10 V
Current: 0–20 mA, 4–20 mA 
Accuracy: ±0.1% of full scale (25°C)
Sampling Rate: 100 samples/sec per channel
Operating Temperature: -20°C to +60°C (-4°F to +140°F)
Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Humidity: 5–95% (non-condensing)
Vibration Resistance: 5–100 Hz

Signal Processing Control PLC Circuit Board

Model Number: PFSK106
Part Number: YM322001-EC
Voltage: 24 V DC (±10%)
Power Consumption: ≤5 W
Digital Inputs: 16 channels 
Flash: 512 KB
Analog Inputs: 8 channels

Power Factor Controller

Sensitivity: ≥ 20 mA.
Frequency range: 50 or 60 Hz +/- 5%
Input current impedance: < 0.1 Ohm
Controller energy consumption: ≤ 15VA
Maximum inductive load AC 250V/2.0A
Voltage: ±1%
Current: ±1%
Power factor: ±1.5%
Active power: ±2.5%
Reactive power: ±2.5%

Digital Slave Output Module

Number of Inputs: 14 digital Output 
Input Type: Sinking or sourcing (configurable)
Input Current: Typically 5-10 mA per input
Isolation Voltage: Typically 500V AC between field and logic side
Response Time: Typically 1-10 ms 
Analog: 20 mA max per channel

Digital Input Module

Number of Inputs: 16 digital inputs
Input Type: Sinking or sourcing (configurable)
Input Current: Typically 5-10 mA per input
Isolation Voltage: Typically 500V AC between field and logic side
Response Time: Typically 1-10 ms 
Analog: 20 mA max per channel

Universal Signal Converter

Brand:ABB
Input Range:0 → 10 V, 0 → 20mA
Mounting Type:DIN Rail
Operating Temperature Range:-20 → +60°C
Minimum Operating Temperature:-20°C
Maximum Operating Temperature:+60°C

Two -synchronous- processors
Flash memory for system and applicationprogram
RAM with battery backup (battery located inBKM-0001)
Data comparators for the processors and theirmemory
Minimum and maximum execution timemonitor
Memory error handler
1oo2D functionality
24V and 5V monitoring
Emergency Shut Down Input (24V)
Two outputs (for non-redundant resp.redundant IO)

ACTUATOR

MODUTROL IV MOTOR
NON-SPRING RETURN
FOOT MOUNTED
4-20 MA MODULATING CONTROL SIGNAL
160 DEGREE STROKE
15-30 SECONDS TIMING
8.5 NM / 75 LB-IN TORQUE RATING
15 VA
120 VAC
50/60 HZ

mm Eddy Current Sensor

Linear Measurement Range 2 mm (80 mils)
Initial Air Gap 0.5 mm (20 mils)
Incremental Scale Factor (ISF)
ISO: 8 V/mm (203.2 mV/mil) ± 5%@ 
temperature range 0 to 45°C(+32 to +113°F)
Deviation from best fit straight line(DSL)
± 0.025 mm (± 1 mil)@ 
temperature range 0 to 45°C(+32 to +113°F)
Minimum Shaft Diameter 25 mm (0.79”)

Driver board

Input Voltage Range: Typically 24V DC
Output Voltage Range: Dependent on the connected load 
Current Rating: Up to 10A 
Power Rating: Typically around 240W 
Operating Frequency: 1kHz to 20kHz