Series:Versamax
Manufacturer:Emerson Automation / GE Fanuc (former)
Part Number:IC200PNS001
Series:VersaMax
Part Number:IC200PNS001
Power Consumption:0.60 Amperes at 5 Volts DC
Product type:Remote I/O Profinet Network Interface Unit
Supported protocol:PROFINET version Version 2.2 Class A IO-Device
Proficy Machine Edition Version Required:Version 7.0 or later
Supported topologies:Linear, Star, Ring (redundant)
No. of Ports:Two (2) RJ45ports
Mounting:DIN Rail
Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CMM004
Product Type:Communications module
No of ports:Two (2) RS232 / RS422 / RS485
Serial Ports:4
Physical Interface:RJ-45
Connectors:RJ45
Supported Configurations:RS-232, RS-422/485
No. of installations per rack:Up to Six (6) modules
Baud Rates:1200 baud to 115.2 kilobaud
Status LED indicators:Module OK, Port Fault, Port Status
Current rating:0.7 mA at 3.3 VDC, 0.150 mA at 5 VDC
Operating Temperature:0 to 60 degrees Celsius
Parity:Even, odd, none
Data bits:7, 8
Stop bits:1, 2
Series:RX3i PacSystem
Part Number:IC695CBL001
Compatibility:PACSystems RX3i
Cable Type:Energy pack cable
Type of Input/Output:Analog
Termination Resistor:Yes
Brand:GE Intelligent Platforms/GE Fanuc
Series:Series 90-70
Part Number:IC697MDL340
Product Type:Output Module
Rated Voltage:120 V AC
Outputs:16
DC Power:No
AC Power:Yes
LED Indicators:Yes
Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG600
Module Type:Universal Analog
No of Channels:Eight (8)
Number of Inputs:8 general purpose
No. of groups:Two (2)
Cold Junction Compensation:2 channels
No. of channels per group:Four (4)
Power Dissapation:5.4W max
Humidity:5 to 95%, non-condensing
Module conversion method:Sigma-delta
Module resolution:11-16 Bits
Internal Power:3.3V: 350mA; 5V: 400 mA
Part Number:IC695PSD140
Product Description:Power Supply module
Input voltage range:85 to 264 VAC 100 to 300 VDC
Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation:None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps
Brand:GE Fanuc
Series:Versamax
Part Number:IC200BEM003
Description:VersaMax master module
Data:3854 input/output
Data Rate:9.6 k baud to 12 M baud
Connector:9 Pin D-sub
Bus Voltage:5 Volts
Slave Devices:125
▪+5.1 VDC output
▪ +24 VDC relay output that can be used to power circuitson Output Relay modules
▪ +3.3 VDC. This output is used internally by RX3i moduleswith IC695 catalog numbers
▪Isolation NONE
▪Ripple (all outputs) 50 mV
▪Noise (all outputs) 50 mV
Display Type: 2 line x 24 characters
Accuracy: 1 % at 25 °C
Power Supply Input: (18 to 32) V (dc)
Network to I/O channel: 277 V (ac)
Power supply input to network: 277 V (ac)
Power supply input to I/O channel: 500 V
Humidity Standards: 20 and 55 °C at 95% for 48hrs
Input Voltage: +24 Vdc at 1 A
Keypad/Display: 30 Multi-function Keypad
Temperature Range: (–40 to +55) °C
Brand:GE Fanuc
Series:RX3i PacSystem
Part Number:IC694MDL742
Type:Output module
Rated Voltage:12/24V DC
Isolation:250V AC continuous;
Electronic Short-Circuit Protection (ESCP):Yes
LEDs:Yes
Hot Insertion and Removal:Yes
Series:Versamax
Part Number:IC200MDL740
Number of Points:16 Outputs
Number of groups:1
Group to Group Isolation:None
Point to Point Isolation:None
Fuse:None
Series:RX3i PacSystem
Part Number:IC695CPE305
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Communication:RS-232
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Maximum Block Size:128 kilobytes
Software: ControlST V04.03.18C
Relative humidity: 5% to 95%, no-condensing
Power Requirements +32 V dc to 18 V dc
Microprocessor: Freescale Power PC
(Power QUICC II PRO 667 MHz)
Memory: 256 MB DDR SDRAM
Manufacturer:GE Fanuc
Series:Versamax
Part Number:IC200ALG240
Product Type:Analog Input Module
Number of Inputs:8
Intelligent Module:Yes
Input Data:16-Bit Input Data
Operating Modes:Current Mode or Voltage Mode
Current Range:1 to 20 milliamps
Voltage Range:-10 to 10 Volts DC
Series:RX3i PacSystem
Brand:GE Fanuc / Emerson Automation
Output Current Range:4 to 20 mA and 0 to 20 mA
Output Voltage Range:0 to 10V and -10 V to +10V
External Supply Voltage Range:20 VDC to 30 VDC
External Power Supply Voltage Ripple:10% (maximum)
Nominal rated voltage:120/240 VAC
Input Power:160 watts maximum at full load
Product Type:Power Supply Module
Load Capacity:100 Watts
No. of Outputs Three (3)
AC Input:90 to 264 VAC
Frequency:47 to 63 Hz
DC Input:100 to 150 VDC
Voltage regulation:5, 12, and -12 VDC
Brand:GE Fanuc
Series:Series 90-70
Part Number:IC697PCM711
Power Supply:1.0 Amp
Connectors:3PL and 4PL
Slot Model:Single-slot Model
PC Programming:Supported
Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693CPU341P
Product Description:Modular CPU
Product type:CPU module
User memory:80 Kbytes
Processor type:80188
Processor speeds:20 MHz
Voltage input:5 Volts DC
Current draw:490 milliamps
Timers / Counters:> 2000
Serial port:1
Current load:490 mA
Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693CPU341N
Product Description:Modular CPU
Product type:CPU module
User memory:80 Kbytes
Processor type:80188
Processor speeds:20 MHz
Voltage input:5 Volts DC
Current draw:490 milliamps
Timers / Counters:> 2000
Serial port:1
Current load:490 mA
