ALL MANUFACTURERS

3300 XL Proximitor Sensor

3300 XL Proximitor Sensor
03 Armored cable with 
connectorprotector
05 CSA, ATEX, IECEx  Approvals

3300 XL Proximitor Sensor

3300 XL Proximitor Sensor
03 Armored cable with 
connectorprotector
00 Not required

3300 NSv Probe

3300 NSv Probe
M10X1 thread, witharmor
10 1.0 meter (39 in)
02 Miniature coaxial ClickLoc 
connector,standard cable
00 Not required

Proximity Probe Housing Assemblies

Aluminum body with 304stainless steel sleeve
28 3300 XL 8mm probe, 
selectablehazardous area approvals
05 0.5 m (20 in)
00 Without fittings
023/4-14 NPT

3300 XL 8 mm Proximity

3300 XL 8 mm Probe
3/8-24 UNFthread
without armor
10 1.0 meter (3.3 feet)
01Miniature coaxial ClickLocconnector 
with connectorprotector, standard cable
00 Not required

3300 XL 11 mm Probe

3300 XL 11 mm Probe
5/8-18 UNF-2A, without armor
10 1.0 meter (3.3 feet)
01Miniature coaxial ClickLocconnector 
with connectorprotector, standard cable
00 Not required

CONTROL MODULE

4139145401S1FX
CONTROL MODULE
SMC-FLEX
STANDARD
120-240 VAC
FLEX QUICK START
150-FS1FX

RTD Input Module

Input Voltage:24V DC
Input Current:10-20 mA
Signal Input Range:0-24V DC
Input Channels:8 or 16
Operating Temperature:-10°C to +60°C 
Storage Temperature:-40°C to +85°C

Digital input Module

Input Voltage:24V DC
Input Current:10-20 mA
Signal Input Range:0-24V DC
Input Channels:8 or 16
Operating Temperature:-10°C to +60°C 
Storage Temperature:-40°C to +85°C

Fieldbus Communication Module

Input Voltage:24V DC
Current Consumption:Typically 100-200 mA
Fieldbus Power:24V DC 
Operating Temperature:Typically -10°C to +60°C
Storage Temperature:-40°C to +85°C

CANopen Communication Module

Communication profile CiA 301 
Number of installed NFLC121 modules 4 max. for FCN-500
Number of slave devices 126 slave devices per 
CANopen Communication Module
Node Bootup
SYNC producer
Heartbeat Consumer/Producer

Relay Output Module

Number of output channels 16
Rated applied voltage 24 to 125 V DC 
100 to 240 V AC, 50/60 Hz
Output response time 12 ms or less
Maximum current consumption 780 mA (5 V DC)
External connection Pressure clamp terminal

Frequency Input Module

Number of input channels 8, isolated channels
Input signal (*1) Contact ON/OFF, voltage pulse
Input frequency 0.1 Hz to 10 kHz
Frequency accuracy 0.1% of reading
Minimum input pulse width 40 μs
Shunt resistance Select from OFF/1000 Ω
Pull-up resistance 68 kΩ (12 V DC or 24 V DC)
Data refresh cycle 10ms
Maximum current consumption 300 mA (5 V DC), 400 mA (24 V DC)

Power Supply Module

100 to 120 V AC
Duplex configuration: Possible
Hot-Swap: Possible
Rated output: +5.1 V DC, 7.8 A
Analog field power supply: Input: 24 V DC ±10 %, 4 A, 
Duplexed (matching-diode)• LED: SYS 
(5 V system power output ON)
FLD (24 V field power supply ON)
Checking terminals: +5 V, +24 V

SB bus repeat module

Transmission method Serial communication
Baud rate 128 Mbps
Transmission distance Max. 8 m per line
Extension units Max. 2 units
Duplex configuration Possible
Supplyvoltage 5 V DC±5%
Currentdissipation Max. 500 mA

Power supply module

Rated input voltage:220 to 240 V AC
Input voltage range:170 to 264 V AC (rms)
Input frequency:47 to 66 Hz (Rating: 50/60 Hz)
Input current: Max. 0.7 A
Fuse rating:3.15 A
Leak current Max. :1 mA
Withstanding voltage:3000 V AC for 1 minute
Insulation resistance:50 MΩ at 500 V DC

Analog Input Module

Input signal 4 to 20 mA 
Allowable input current 24 mA 
Accuracy ±0.1% of full scale 
Overcurrent protection Provided 
Data refresh cycle 10 ms
Input step response time 100 ms
Temperature drift Max. ±0.01%/°C

Base module

Operation -40 to +70 °C 
Transportation/storage -40 to +85 °C
Dust 0.3 mg/m3 or less
Protection class IP20
Altitude 3000 m or less
Electric field 3 V/m or less (26 MHz to 1 GH
Magnetic field 30 A/m (AC) or less, 400 A/m (DC) or less

ENGINE MANAGEMENT SYSTEM

ENGINE MANAGEMENT SYSTEM
Pentium® 133 MHz PC
32 MB of RAM
DOS 6.22, Windows® 95
DIGITAL
100 HZ MAX. FREQUENCY
5 V OUTPUT
RS-232 COMMUNICATION PORT

OVERSPEED MONITOR

LOW SPEED : 1677 Hz
OVERS SPEED : 12077 Hz
INPUT POWER : 24V DC 50mA
RELAY CONTACTS : 30V DC 2A
GROUPS A,B,C,D T5 -20'C TO +85'C

General Purpose Equipment Monitor

01 110 to 220 Vac @ 50 to 60 Hz (externalsupply)
00 No display
03 Fiberglass NEMA 4X/IP66 WP housingwith window in door
00 None
00 None
EQUIPMENT MONITOR
GENERAL PURPOSE
1900/65A SERIES

Embedded Controller Module

Product Type: PAMC Acoustic Monitor (Processor)
Software: ControlST V04.03.18C
Relative humidity: 5% to 95%, no-condensing
Power Requirements +32 V dc to 18 V dc
Microprocessor: Freescale Power PC (Power QUICC II PRO 667 MHz)
Memory: 256 MB DDR SDRAMs

Processor Module

Freescale™ QorIQ P4080 – 
8-core CPU @ 1.5GHz
Serial Rapid IO, PCIe 
and 1/10GbE fabrics
Fast dual-channel memory 
(up to 8 GB RAM with ECC)
Useable in managed (with MCH) 
and unmanaged (without MCH) systems

Drive Board

24V DC for logic power
230V to 690V AC
Approximately 10-20W
0 Hz to 200 Hz
Standard range: -10°C to +50°C
Storage Temperature:-40°C to +85°C
5% to 95% RH, non-condensing

Operator Interface

PC BOARD
DISPLAY CONTROL BOARD
DIGITAL DISPLAY