ALL MANUFACTURERS

COBUX-HW INTERFACE CARD

Type: COBUX-HW Interface Card
Operating Voltage:24V DC
Operating Temperature Range:-20°C to +70°C
Storage Temperature Range:
-40°C to +85°C.
Analog inputs: 0–10 V, ±10 V, 4–20 mA 
Analog outputs: 0–10 V, 4–20 mA 

SOE Time Keeper Master

Analog inputs: 0–10 V, 4–20 mA
Analog outputs: 0–10 V, 4–20 mA
Power Supply:24 V DC (±10%)
Supply Voltage：24V DC (19.2–28.8V) via backplane
Power Consumption：1.8W (typical), 2.5W (max)
Isolation 1500V AC (channel-to-logic)

Control Board

Power Supply:24 V DC 
Differential: ±12 V.
Power consumption: < 5 W
Single-ended: 0–24 V
Output Voltage:
TTL: 0–5 V.
HTL: 0–24 V

MICROMASTER 440 WITHOUT FILTER

MICROMASTER 440 
without filter 380-480 V 
3 AC +10/-10% 47-63 Hz 
constant torque 15 kW 
overload 150% 60 s, 
200% 3 s square-law torque 18.5 kW 
520x 275x 245 (HxWxD) 
degree of protection IP20 ambient 
temperature -10+50 °C 
without AOP/BOP

MICROMASTER 440 WITHOUT FILTER

MICROMASTER 440 
without filter 380-480 V 
3 AC +10/-10% 47-63 Hz 
constant torque 5.5 kW 
overload 150% 60 s, 
200% 3 s square-law torque 7.5 kW 
245x 185x 195 (HxWxD) 
degree of protection IP20 
ambient temperature -10+50 °C 
without AOP/BOP

Pulse Input Module

8 pulse input channels
Voltage Range: 5–30 V DC 
Standard: 0–10 kHz
Frequency Measurement: ±0.01% of reading
Channel-to-Channel Isolation: ≥ 1500 V AC/DC
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Storage Temperature:
-40°C to +85°C (-40°F to +185°F)
Humidity:
0–95% non-condensing

Pulse Input Baseplate

Frequency/Rate: Up to 10 kHz 
Voltage Range: 5–30 V DC
Counting Resolution: 24-bit 
Frequency Accuracy: ±0.01%
Channel-to-channel isolation: ≥ 1500 V AC/DC
Field-side Power: 24 V DC
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Storage Temperature:
-40°C to +85°C (-40°F to +185°F)

TERMINAL BLOCK

PRESSURE CLAMP TERMINAL BLOCK
STARDOM
BASIC TYPE
FOR CONNECTION USE WITH ANALOG
12 CHANNEL MODULE

TERMINAL BLOCK

PRESSURE CLAMP TERMINAL BLOCK
STARDOM
BASIC TYPE
FOR CONNECTION USE WITH ANALOG
12 CHANNEL MODULE

19 INCH RACK

Max number of mountable I/O modules:8 
Number of mountable Power suply modules:2 
S Standard type
0 19-inch rack-mounted
BASE MODULE
STYLE S1
STANDARD TYPE
19 INCH RACK
DIN MOUNT
(92F306027)

Serial Communication Module

Interface:RS-422/RS-485 (2 ports)
How connected:Multipoint
How communicates Half-duplex/Full-duplex
How synchronizes Start-stop synchronization
Transmission code ASCII/binary
Character length:7/8 bits
Stop bit :1/2 bits
Parity check None/even/odd
Transmission distance Maximum:1200 m
Current consumption:500 mA

RTD Input Module

Number of input channels:12, isolated
Allowable input voltage:±5 V
Between input and system: 1500 V AC for 1minute
Power ON :2 MΩ or more
Power OFF: 2 MΩ or more
Allowable total resistance of signalsource plus wiring:40 Ω or less 
Effect of allowable signal source resistance (1000 Ω): ±20 μV
Measurement current:1 mA
Temperature drift:Max. ±30 ppm/°C 
Maximum current consumption:450 mA (5 V DC)

RTD Input Module

Allowable input voltage ±5 V.
Withstanding voltage :1500 V AC for 1minute 
Power ON 2 MΩ or more
Power OFF 2 MΩ or more
Accuracy ±0.03% of full scale (for 0 to 400 Ω)
Allowable total resistance of signalsource plus wiring:40 Ω or less 
(wiring resistance per wire)
Temperature drift:Max. ±30 ppm/°C.
Maximum current consumption:450 mA (5 V DC)

Digital Input Module

Number of input channels:32
Rated input voltage:24 V DC
Input ON voltage:18 to 26.4 V DC
Input OFF voltage:5.0 V DC or less
Input current (at rated input voltage):4.1 mA±20 % / channel
Instantaneous allowable maximum input voltage:30.0 V DC
Input response time:8 ms or less
Minimum ON detection time:20 ms 
Maximum ON/OFF cycle:25 Hz
Maximum current consumption:500 mA (5 V DC)

Digital output module

Number of output channels:64
Rated applied voltage:24 V DC
Load voltage:24 V DC, 100 mA
Field power supply voltagerange:20.4 to 26.4 V
Output ON voltage maximumvalue:2 V DC
Leak current maximum valuewhen output OFF:0.1 mA
Output format:Current sink

Analog input module

Number of input:channels16, non-isolated
Input signal:4 to 20 mA
Allowable input current/voltage:27 mA
Accuracy:±0.1% of full scale
Data refresh cycle:10 ms
Input step response time:100 ms
Transmitter power supply:22.8 to 26.4 V 
Setting of 2-wire or 4-wiretransmitter 
For each channel by setting pin

Power supply module

Power supply module 
(220-240 V AC input)
Standard type with no explosionprotection
Basic type
With ISA Standard G3 option

Central Braking Module

SINAMICS S120 
Central Braking Module 
Input: 1070-1115 V
1200 kW

PROFINET Controller Gateway Module

Series:Mark VIe/Mark VIeS
Product Type:PROFINET Gateway Module
Processor Type:1066 MHz EP80579 Intel
Operating Temperature:22 to 149°F
Manufacturer:General Electric

op Box A Module Board

Series: Mark VIe
Channels: Configurable for 16–32 analog/digital channels
Analog: 4–20 mA, 0–10 V, RTD
Digital: 24 VDC dry/wet contacts
Supply Voltage: 24 VDC nominal
Power Consumption: Typically ≤ 8 W
Operating Temperature: -40°C to +70°C (-40°F to +158°F)

Top Box B Module

Series: Mark VI 
Supply Voltage: Typically 24 VDC 
Power Consumption: Varies by load 
Operating Temperature: -40°C to +70°C
Humidity: 0–95% non-condensing

Measurement and counter module

Measurement and counter module
Modicon Premum
2 channels modularity
thermal tripping protection
7 to 10W
10kHz

Power supply module

Power supply module
Modicon Premium
input current of 300mA
secondary power of 26W
85 to 264VAC

TSXDEY16A5

Modicon Premium
16 inputs
compatible with 
2/3 wires proximity sensors
0.83W, 15mA

USB annunciator/numeric keyboard

Power Requirements 5 VDC, ± 5% a
USB Annunciator Keyboard: 300 mA (max)
Output Impedance: 1200 Ohms Nominal
Nominal Level: 0.437 to 0.133
Peak to Peak Amplitude, Vpp: 0.872
Operating Temperature 0 to 40°C (32 to 104°F)
Storage Temperature -40 to +70°C (-40 to 158°F)
Humidity range, storageand operating:
20% to 80%, non-condensing