General Electric

SAFETYNET CONTROLLER CARRIER

SAFETYNET CONTROLLER CARRIER 
WITH EARTH LEAK DETECTION
GE INTELLIGENT PLATFORMS
(PAC8000)

POWER SUPPLY MONITOR

POWER SUPPLY MONITOR
PAC8000 I/O
NODE SERVICES
12 V DC
30 MA

Reflective Memory PCI Node Card

PC BOARD
REFLECTIVE MEMORY
PCI NODE CARD
128 MBYTE MEMORY
MULTIMODE TRANSMISSION
Low Latency, Deterministic Transfer Rates
Operating System and Bus Structure Independence

Serial Modbus Communication I/O Module

Dual-port RS-232/RS-485 
Baud rates up to 115.2 kbps
Voltage Levels: ±5V to ±15V
Max Cable Length: 15m (50 ft)
Supply Voltage: 24V DC (±10%) 
Power Consumption: 3W typical

Wind Top Box A Module

Power Supply: 28 VDC
Communication Ports: Ethernet, Serial
Operating Temperature: -40°C to +70°C
Storage Temperature: -55°C to +85°C
Humidity: 5–95% non-condensing

High Capacity power supply

Series:90-30 PLC
Brand:GE Fanuc
Product Type:High-capacity power supply
Protocol Support:RS485 
Nominal Rated Voltage:24VDC / 48VDC
Input Voltage Range, DC:Start: 21 to 56 VDC Run: 18 to 56 VDC
Voltage:24 Volts DC
Standard:UL, CE
Full load power rating:50 Watts

VIBRATION MODULE

Velocity: 0–20 mm/s
Displacement: 0–500 µm 
Frequency Range:10 Hz – 10 kHz 
A/D Resolution:16-bit
Sampling Rate:Up to 50 kHz
Power Supply:24V DC 
Power Consumption:5W typical

I/O Protection Module

Accessory Boards:8 Boards
Ambient Temperature Rating:-30 to 65 Degrees Celsius
Base Circuitry Coating:Special Protection
Assembly Type:IS220 Standard Modular
Chassis Style:Rough Vented
Port Styles:2 Ethernet (Pictured)
Operating temperature: -30 to 65oC
Power Supply Voltage: 24 V dc

Rack Power Supply Module

Number of channels: 6
Input span: 4-20 mA
Termination resistors: 121 Ohm
Technology: Surface Mount
Common Mode Voltage Range: ±5 V
Maximum Lead Resistance: 15Ω
Analog output current: 0-20 mA
Operating temperature: -30 to 65 °C

Turbine I/O Module

Operating Voltage:24 VDC (±10%)
Power Consumption:12W (typical), 18W (max)
Isolation :1500 VAC (field-to-logic)
MPU Input Impedance:100 kΩ (differential)
Speed Resolution:1 RPM (0.0167 Hz)
Accuracy:±0.02% of reading 

Backup Protection I/O Module

Operating Voltage:24 VDC (±10%)
Power Consumption:10W (typical), 15W (max)
Isolation:1500 VAC (field-to-logic)
Backplane Current:5VDC: 1.2A max
Range: 0–250 mV / ±10V (software-selectable)
Resolution: 16-bit
Accuracy: ±0.1% FS

Flame Detector Power Supply

IS220PSFDH1A
POWER SUPPLY
335V
IO PACK

ARCNET Interface I/O Module

ARCNET INTERFACE MODULE
OPTIMIZED FOR MARK VI AND MARK VIE SYSTEMS
Voltage Range: 11–30 VDC (sinking)
Operating Voltage:24 VDC
Isolation:1500 VAC 

POWER METER

Operating Voltage:85–265V AC/DC
Nominal: 120/208V
Maximum: 690V AC 
Burden: <0.2VA per phase
Standard CTs: 1A or 5A
Burden: <0.1VA at 5A
Voltage/Current: ±0.2% of reading
Power/Energy: ±0.5% 
Frequency: ±0.01Hz

Current Source I/O Block

I/O MODULE
GENIUS BLOCK
CURRENT SOURCE ANALOG
4 INPUT / 2 OUTPUT
24/48 VDC POWER
4-20 MA CURRENT INPUTS AND OUTPUTS

Servo Driver Board

Input Voltage:24V DC (±10%)
Power Consumption:15W (typical)
Isolation Voltage:1500V AC
Analog Inputs:±10V
Control Bandwidth:1kHz (typical)
Resolution:16-bit
Update Rate:62.5μs (16kHz)

Printed Circuit Board

Series:Mark VI Speedtronic
Functional Acronym:BPPB
Input Voltage: 24V DC
Output Voltages:+5V DC @ 20A max
Efficiency: >90% typical
Ripple: <50mV p-p on all outputs
Multi-Voltage Power Distribution: Provides +5V, ±15V

Optional Auxiliary Board

Input Voltage: 24V DC ±10%
Power Consumption: 8W typical
Analog Inputs:8 channels
Digital I/O:8 channels
Vibration: 5-500Hz
Extended I/O Capacity: 16 analog/digital channels

Printed Circuit Board

Input Voltage: 24V DC
Output Voltages:+5V DC @ 20A max
Power Efficiency: >90% typical
Ripple & Noise: <50mV
Vibration: 5-500Hz

Optional Auxiliary Board

Input Voltage: +24V DC
Power Consumption: <10W
Channels: 8 or 16 
Signal Range: 4-20mA
Resolution: 16-bit ADC
Voltage Levels: 24V DC

Power Converter

Input Voltage:24 V DC
Output Voltage:±15 V DC or +5 V DC 
Output Current:Up to 10 A
Power Rating:120–150 W
Efficiency:≥85% (typical)
Ripple & Noise:<1% of output voltage 
Voltage Regulation:±1% (line and load)

DC Power Supply Feedback Board

PC BOARD
DC POWER
FEEDBACK
MARK 5
TURBINE CONTROL
MULTI INPUT/ OUTPUT
ON BOARD RAM

VME SERVO CARD

RAM: 64–128 MB SDRAM
Non-Volatile Storage: 16–32 MB Flash
Channels: 4–8 channels
Signal Type: ±80 mA current output 
Resolution: 16-bit DAC.
Accuracy: ±0.1% FS (Full Scale).
Update Rate: 1–10 kHz 

Drive Control Card

Firing Angle Range:0–180°
Synchronization:3-phase AC input 
Pulse Output:8–12 channels
Accuracy:±0.5° firing angle resolution
Isolation :2500V AC
Power Supply:+5V DC

Discrete Input Terminal Board

Input Channels:32 optically isolated inputs
Input Type: 24–125V DC
Voltage Range:24V DC 
Input Current :5–15mA per channel
Isolation :1500V AC
Response Time:≤10ms (ON/OFF)
Power Supply:+5V DC

Phase Logic Interface Board

Input Channels:3-phase voltage
Voltage Range:0–150V AC
Frequency Range:45–65Hz 
Accuracy:±1% of full scale 
Response Time:<2 cycles
Isolation:2500V AC 
Power Supply:+5V DC

DRIVE CPU BOARD

DRIVE BOARD
PRIMARY DRIVE CONTROLLER
MARK V
32-bit microprocessor
EPROM (Firmware storage)
RAM
Communication ICs
I/O interface circuitry

INTERFACE COMMUNICATION CARD

PROGRAMMER MODULE
INTERFACE COMMUNICATION CARD
MARK 5
TURBINE CONTROL
MULTI INPUT/ OUTPUT

Emergency Overspeed Board

Supply Voltage:24V DC ±10% 
Power Consumption:7 W (idle), 10 W (max)
Isolation:1500V AC 
MPU Signal Range:10–250 V RMS
Processor:3× 32-bit DSPs

Emergency Overspeed Board

PC BOARD
EMERGENCY OVERSPEED BOARD
MARK V
Supply Voltage:24V DC ±10% 
Power Consumption:8 W 
Isolation:1500V AC 

I/O Engine CPU Board

DRIVE BOARD
PROCESSOR CARD
DAUGHTER BOARD
UC2000
MARK V

UC2000 Motherboard

CIRCUIT BOARD ASSY
DS200UCIAG1A
Series:Mark V
Part Number:DS215UCIAG1AZZ05A
Functional Description:UC2000 Motherboard
Functional Acronym:UCIA
PCB Coating:Normal Coating
Assembly Type:DS215 Special Assembly

Gate Distribution and Status Board

Supply Voltage: +24 V DC (±10%) 
Power Consumption: ≤10 W
Isolation Voltage: 2500 V AC
Voltage: +15 V / -10 V 
Response Time: ≤1 μs for fault detection.

Exciter HS Relay Driver Board

Supply Voltage: +24 V DC
Power Consumption: ≤15 W 
Isolation Voltage: 1500 V AC
Voltage Range: 24–125 V DC
Current Rating: Up to 5 A per channel
Switching Speed: ≤10 ms 

Protective Termination Expander Board

PC BOARD
EOS PRINTED CIRCUIT BOARD
MARK 5
Input Voltage:24 VDC ±10%
Power Consumption:8W (typical)
Isolation:1500 VAC
Digital Inputs :24VDC

RXi Controller

RXI CONTROLLER / PACSYSTEMS
HIGH PERFORMANCE DISTRIBUTED IO
PROGRAMMABLE
REQUIRES ICRXIACCIDM001A

Common Analog I/O Board

Series: Mark V
Product Type: Terminal Board
Input Channels: 8 Analog Inputs
Input Resolution: 12-bit / 16-bit
Output Type: Voltage (0-10V, ±10V)
Output Resolution: 12-bit / 16-bit
Input Type: Voltage (0-10V, ±10V)
Communication Protocol: RS-485
Power Supply: 24V DC ±10%, < 5W
Isolation: 1500V

Simplex Trip Board

TRIP CONTROL CARD
PC BOARD SDCC MARK V SYSTEM
Analog Trip Signals: 4–20 m
Digital Trip Signals: 24 VDC
Aux Relay (K2): Alarm/status outputC
Resolution: 0.1% of setpoint
Accuracy: ±0.25% FS
Voltage: +24 VDC (±10%)
Consumption: 15 W (max)

DOS DUP Processor Board

PC BOARD
MARK 5 SERIES
TURBINE AND GAS CONTROL BOARD
WITH ON-BOARD MEMORY
MULTI-INPUT/OUTPUT

Power Connect Card

Series: EX2000
Microprocessor: Intel Ultra Low Voltage Celeron 650 MHz
Operating System: QNX Neutrino
Operating Temperature: 0 to 60°C
Product Type: Power Connector
Analog Input current: 240 V rms
DC Bus Voltage: 125 VDC
Auxiliary Voltage: +15 VDC

Single Board Computer

VME-7807 Series 
SINGLE PCB BOARD 
PROCESSOR: 1.8GHZ PENTIUM M DDR 
SDRAM: 1 GB L2 CACHE: 2MB 
FLASH: 512 KB 1101.10 
FRONT PANELSCAN DISK 2GBITES

Vibration Input Terminal Board

Series:Mark VIe Speedtronic
Part Number:IS200TVBAH2A
Functional Acronym:TVBA
Functional Description:Vibration Input Terminal Board
PCB Coating:Conformal Coating
Functional Revision 1:B

RX3I PROFINET SCANNER MODULE

RX3I PROFINET SCANNER MODULE
10/100/1000 WITH FOUR PORTS
1.2AMP @ 3.3VDC
1.1AMP @ 5 VDC
SINGLE SLOT

Terminal block

I/O BASE
BARRIER STYLE
2 TIER BOX TERMINAL

Terminal block

I/O BASE
BARRIER STYLE
2 TIER BOX TERMINAL

Thermocouple Input Module

ANALOG INPUT MODULE
THERMOCOUPLE
8POINT
INDEPENDENT THERMOCOUPLE OR MULTIVOLT INPUTS
50/60HZ

small form-factor pluggable scanner module

Type:Scanner module
Speed:100 Mbps
Material:Multi-mode fiber (MMF)
Length:2 Kilometers
SD Card:Supported
Power:3.3 to 5 Volts
Port Connectors:Two RJ-45 and two SFP cages.
LED Indicators:Yes

Terminal board

Series: GE Mark VIe Series
Input Voltage: 24 V DC (±10%)
Power Consumption: ≤8 W 
Voltage Range:0–30 V DC or 0–120 V AC
Range: 0–10 V DC, 4–20 mA
Resolution: 16-bit ADC
Type: Form-C contact relays (1 A at 30 V DC)
Operating Temperature: -40°C to +70°C
Relative Humidity: 5–95% (non-condensing)

TERMINAL CONTACT BOARD

Series: GE Mark VIe Series
Input: 24 V DC (±10%)
Isolation: ≥1.5 kV
Digital Inputs:0–30 V DC
Analog Resolution:16-bit ADC
Operating Temperature: -40°C to +70°C 
Shock/Vibration: to 5 G (5–500 Hz)

TERMINAL CONTACT BOARD

Series: GE Mark VIe Series
Terminal Capacity: ≤32 AWG
Input Voltage: 24 V DC (±10%)
Power Consumption: <5 W 
Galvanic Isolation: Up to 1.5 kV AC/DC
Voltage Range for Inputs: 0–120 V AC/DC
Digital Inputs (DI):30 V DC/120 V AC
Operating: -40°C to +70°C
Storage: -40°C to +85°C
Humidity Tolerance: 5–95% non-condensing

Turbine Emergency Trip Board

Series: GE Mark VIe
Dual Power Inputs: Isolated 24 V DC
Fail-safe relay contact rating: 2 A at 24 V DC
Input Voltage: 24 V DC (±10%)
Temperature Range: -40°C to +70°C (continuous operation)
Surge Protection: TVS diodes/SRC filters on I/O channels
Relative Humidity: 5–95% (non-condensing)

RTD Input terminal board

Operating Voltage:24 V DC ±10%
Power Consumption: <10 W 
Types: 2-wire, 3-wire
Number of Inputs: 8 channels
Excitation Current:1 mA 
Measurement Resolution: ≤0.1°C

Relay Output Terminal Board

Series: Mark VIe
Product Type: Relay Output Terminal Board
Number of channels: 16
Relay Type: SPDT
Relay Contact Rating: 10A
Input Voltage Range: 12V, 24V
Number of Relay Channels: 4, 8
Relay Switching Current: Max 10A
Mounting Type: DIN rail
Output Resolution: 12-bit
Output Impedance: 10 Ohm
Analog outputs: 0-20 mA

Vibration terminal board

Series: GE Mark VIe
Input Voltage: 24 V DC (±10%)
Power Consumption: ≤15 W
Proximity Probes: 0–10 kHz
Accelerometers: Up to 20 kHz
IEPE sensor excitation:typically 18–24 V DC
Analog input: ±10 V peak 
Operating Temperature: -40°C to +70°C.
Humidity Tolerance: 5–95% (non-condensing)

Transient Data Interface Module

Input Voltage: 24 V DC (±10%)
Power Consumption: Typically <20 W
Sampling Rate:Up to 25.6 kS/s
Voltage ranges (analog): Typically ±10 V DC
Analog Input: 16-bit
Operating Temperature: -40°C to +70°C 
Storage Temperature: -40°C to +85°C.
Relative Humidity: 5%–95% (non-condensing)

SERVO AMPLIFIER MODULE

A06B6290H106
SERVO DRIVE
SERVO AMP
SERVO AMPLIFIER MODULE AISV 180HV
SERVO DRIVE MODULE AISV 180HV-B
FOR 30I-B SERIES
CNC

I/O Pack processor board

Processor Type:Mark VI 
Backplane Power: +5 VDC
Analog: ±10 V, 4–20 mA
Digital: 24 V DC
Processing Speed: 100–200 MHz 
Non-Volatile Memory (Flash):16–64 MB

CPU RAM backup battery

AUXILARY BATTERY MODULE
15.0 AMP-HOURS
COMPATIBLE WITH ALL BATTERY 
CONNECTORS ON IC693 POWER SUPPLIES
MEMORY BACKUP BATTERY

Ethernet network interface unit

RX3I NIU WITH TWO SERIAL PORTS
20K OF LOCAL LOGIC
MODULE REQUIRES UNIVERSAL BASE (IC695CHSXXX)
REQUIRES ETHERNET MODULE (IC695ETM001)
NIU SUPPORTS ALL RX3I I/O MODULES

Operator Interface

QUICKPANEL TEXT
LCD
COMMUNICATIONS OUTPUT

SCANNER MODULE

IC695PNS001
RX3I PROFINET SCANNER MODULE
10/100/1000 WITH FOUR PORTS
1.2AMP @ 3.3VDC
1.1AMP @ 5 VDC
SINGLE SLOT

PACSystems RX3i Universal Backplane

PACSystems RX3i Universal Backplane
(IC695 Series), occupies 1 slot
24 Vdc Nominal Operates 18Vdc to 30 Vdc
40 W Total, All Loads
14 AWG to 22 AWG, 1 wire per terminal
Power, P/S Fault, Overload, Overtemperature

Emergency Turbine Protection Module

Frame Rate Up to 100 Hz
MPU Pulse Rate Range 2 Hz to 20 kHz
Input supply: 125 V dc (70-145 V dc)
Output: 5 V dc and 28 V dc
Input Channels:4–20 mA

Industrial Circuit Board

Analog Inputs: 4–8 channels
Analog Outputs: 4–20 mA or ±10 V DC
Digital I/O: 24 V DC 
Form Factor: 6U VME module 
Operating Temperature: -20°C to +70°C (-4°F to +158°F)
Humidity: 5–95% RH (non-condensing).

VME Controller Board

System: Mark VI Turbine Control System
Clock Speed: ≥1 GHz 
RAM: 1–2 GB DDR3
Flash Storage: 4–8 GB 
Form Factor: 6U VME module
Voltage: 24 V DC (±10%) 
Power Consumption: ≤25 W

VME Monitor Board

Analog: 4–20 mA, ±10 V DC
Digital: 24 V DC dry/wet contacts
Frequency: Vibration signals
Form Factor: 6U VME module
Data Acquisition:16-bit ADC resolution
Sampling rates up to 50 kS/s 
Backplane: VME P1/J1 connectors for bus communication

Exciter DC Feedback Board

Voltage Feedback: 0–500 V DC
Current Feedback: 0–10 A DC
Accuracy: ±0.25% of full scale
Frequency Response: Up to 100 Hz
Signal-to-System Isolation: 1500 V AC
Common-Mode Rejection: >60 dB at 50/60 Hz
Analog Output: 4–20 mA or 0–10 V DC