Protocol: Profibus-DP
Data Transfer Rate: 9.6 kbps to 12 Mbps
Max. Number of Slaves: Up to 125 devices
Cable Length:Up to 1200 m
Connector Type: 9-pin D-sub
Bus Voltage: 5V logic
Protection Functions:3-Phase Overcurrent (OC)
Rated Frequency:50/60 Hz
Rated Current (Iₙ):1 A or 5 A
Auxiliary Supply:24/48/110/125 V DC
Rated current:1 A
continuously:4 A
Input impedance:<100 mΩ
Local Bus Power :12 VDC at 150 mA
Bussed Field Power:24 VDC at 3.2 A/Card
Field Circuit:24 VDC at 100 mA/Channel
Ambient Temperature:-40°C to +70°C
Shock:10g ½ Sinewave for 11msec
Vibration:1mm Peak to Peak from 2 to 13.2Hz;
0.7g from 13.2 to 150Hz
ANALOG INPUT MODULE
32 CHANNEL
P72122-4-0788722
Current: 4–20 mA, 0–20 mA
Voltage: 0–10 V, ±10 V, 1–5 V
Resolution: 16-bit
Accuracy: ±0.1% of full scale
Input Voltage Range: 380-480V AC (3-phase)
Output Voltage: 12-600V DC
Charging Current: 10-100A
Efficiency: >92%
Frequency: 50/60Hz ±5%
Voltage Accuracy: ±0.5% of full scale
Current Accuracy: ±1% of full scale
16-channel Analog Output Field Termination Assembly
Output Type:4-20 mA
Output Channels:16
Output Readback Accuracy:±4%
Output Current Linearity:± 0.05% nominal
Resolution:± 0.05%
Directly Settable Output Current Range:0 mA, 2.9 mA to 21.1 mA
Output Ripple:100 mV peak-to-peak at power line frequency
Power Supply: 10.5–30V DC
Analog: 4–20mA
Digital: PROFIBUS DP/PA
Position Feedback: 4–20mA
Control Accuracy: ±0.5% of span
Supply Pressure: 1.4–7 bar (20–100 psi)
Output Pressure: 0–100% of supply pressure
Air Consumption: < 0.12 Nm³/h
Response Time: < 1 sec
Nominal On-State Current (ITAV):2000A*
Maximum Surge Current (ITSM):20kA (1ms)
Critical di/dt:500A/μs
Maximum Blocking Voltage (VDRM):1700V
Repetitive Peak Reverse Voltage (VRRM):1700V
Gate Trigger Voltage (VGT):1.5-2.5V
Recommended Switching Frequency:≤500Hz
Nominal On-State Current (ITAV):2500A
Peak Surge Current (ITSM):25kA (1ms)
Critical di/dt:800A/μs
Maximum Blocking Voltage (VDRM):4500V
Repetitive Peak Reverse Voltage (VRRM):4500V
Gate Trigger Voltage (VGT):1.5-2.5V
Repetitive Blocking Voltage:4500V
Non-Repetitive Blocking Voltage (VDSM):4500V
Gate Trigger Voltage (VGT):1.5-2.5V
Average On-State Current (ITAV):3500A
Peak Surge Current (ITSM):30kA (1ms)
Critical di/dt:1000A/μs
Peak Gate Current (IG):50A
Gate Power Dissipation:20W
Blocking Voltage : 4500V Maximum Repetitive Off-State Voltage: 4500V Gate Trigger Voltage (VGT): 1.5-2.5V Average On-State Current : 3500A Turn-On Time (ton): <5μs Turn-Off Time (toff): <10μs Switching Frequency: Up to 500Hz
Blocking Voltage:4500V
Gate Trigger Voltage (VGT): 1.5V to 2.5V
Peak Surge Current (ITSM):30kA
Turn-On Time (ton): <5µs
Turn-Off Time (toff): <10µs
Switching Frequency: Up to 500H
Gate Current (IG): 50A
S-Series DI 32-Channel 24 VDC
Dry Contact Card
Input Voltage Range:5–60V DC (24V DC nominal)
On-State Threshold:≤ 5V DC (logic "1")
Off-State Threshold:≥ 15V DC (logic "0")
Input Impedance:3.3 kΩ (typical)
Input Current:≤ 8 mA @ 24V DC (per channel)
Max Continuous Voltage:60V DC
Isolation:Group-to-Group: 300V AC RMS
Channels: 8
Signal Type: 4–20 mA DC
nput Range:4–20 mA DC (configurable for 0–20 mA)
Overrange Capability: -1 mA to +25 mA
Input Impedance:≤ 250 Ω (typical)
Accuracy:±0.05% of span (at 25°C)
Temperature Drift:±0.005% of span/°C (-40°C to +70°C)
Resolution:24-bit
AO 8-CHANNEL 4-20MA HART CARD
12P4704X032
Channels: 8
Signal Type: 4–20 mA DC
Output Range:4–20 mA DC
Load Resistance:300–1100 Ω
Accuracy:±0.1% of span (25°C)
Temperature Drift:±0.02% of span/°C (-40°C to +70°C)
Resolution:15 bits (including sign)
Signal Type: 4–20 mA DC
Standard: 4–20 mA DC
Overrange: -5 mA to +25 mA
Input Impedance: ≤ 250 Ω (typical)
Field Power 30 VDC at 200 mA
AmbientTemperature-40°C to +70°C
Shock 10g ½ Sinewave for 11msec
Response time :≥ 20 ms
Current input max. 0.6 A
Fuse (external) 10 A time-lag (T)
Back-up battery None
Operating voltage 24 VDC, -15...+20 %, rPP ≤ 15 %
Switching voltage 5 V, 250 VAC / 250 VDC
Number of channels 8 potential-free normally open contacts
64532588
Interface Board
ADPI-01 PANEL INTERFACE
Power Supply:24V DC
Consumption: 15W (typical)
Operating Voltage:18–30V DC (±10%)
Isolation:500V AC between ports and power
Interface Connector: USB A type x 2
Operation Keyboard Function : USB 2.0
Sound Function : USB 1.1
Input Voltage: 5 V±5 %
Maximum Consumption Current: 1 A
Chassis Color: Black
Processor:Dual-core CPU
Memory:512 MB RAM
Flash Storage:1 GB internal
Power Supply:24 V DC
Communication Ports
2x Ethernet (RJ45): 10/100/1000 Mbps
1x Serial (RS-232/485): For legacy devices (MODBUS RTU).
1x USB 2.0: For engineering access.
POWER SUPPLY BOARD
WITH JUMPER WIRE
Primary Input: 18–32 V DC
Backup Input: 24 V DC
Output Voltage: 24 V DC
Output Current: 6 A
Holdup Time: ≥48 hours
Efficiency: >85% (typical).
Ripple & Noise: <100 mV peak-to-peak
USB-Hardlock Key for ECT with 1 licence
Encryption:AES-128/256-bit
Hardware ID:Unique 64-bit serial number
Operating Voltage:5V DC
Power Consumption:≤ 100 mA
Input Voltage:+24 Vdc at 1 A
Keypad/Display:30 Key Multi-function Keypad
Operating Temperature:–20 to +60 °C
Outputs:2 Actuator Outputs, 8 Relay Outputs
6 Programmable Current Outputs
Slot Type:Supports RS-232, RS-422, and RS-485 hardware
Software Version:OpView™ and 505View
Storage Temperature:–40 to +85 °C
Rated Current:1 A or 5 A
Rated Voltage:48–250 V AC/DC
Burden:< 0.5 VA
Contact Rating:5 A @ 250 V AC
Mounting:Panel-mounted
Operating Temperature:-25°C to +55°C
From the vibro-meter® product line
Ex certified versions for use in hazardous areas
TQ401 conforms to API 670 recommendations
5 and 10 m systems
Temperature-compensated design
Frequency response:DC to 20 kHz (−3 dB)
Measurement range:2 mm
Temperature range:−40 to +180 °C
From the vibro-meter® product line
Ex certified versions for use in hazardous areas
TQ401 conforms to API 670 recommendations
5 and 10 m systems
Temperature-compensated design
Frequency response:DC to 20 kHz (−3 dB)
Measurement range:2 mm
Temperature range:−40 to +180 °C
Communication Protocol:Modbus RTU over RS‑485
Display:128 × 64 pixel LCD
Keypad:5-button navigation
LED Status Bar:Yes (visual feedback)
Power Supply:24 V DC
Operating Temp:–20 °C to +70 °C
Storage Temp:–40 °C to +85 °C
Humidity:0–95 % RH, non-condensing
Galvanic isolation
Open wire detectio
Optional redundancy
Direct / Reverse Input Indication
Supplies Non-incendive field power
Internal or external field power selection
Extensive internal diagnostics for data integrity
Input Voltage:100–240 VAC (universal)
Output Voltage:24 VDC (adjustable up to ~27 V)
Output Current:20 A continuous
Protections:Overcurrent, overvoltage, short-circuit
Operating Temperature Range:–25 °C to +70 °C
Supply voltage: 24 V DC
Reset input voltage: 18 - 70 V DC
Reset input current: 1.1 mA at 24 V DC
Earth fault threshold: 5.5 mA (± 1 mA)
Max. earth current: 25 - 32 mA
Supply voltage: 24 V DC
Reset input voltage: 18 - 70 V DC
Reset input current: 1.1 mA at 24 V DC
Earth fault threshold: 5.5 mA (± 1 mA)
Max. earth current: 25 - 32 mA
Max. output current: 2 A
Isolation 1500 V DC / 1000 V AC
Initial contact resistance: 30 mW
Operating temperature: -5°C-+50°C (23°F-+122°F)
Max. output voltage: 36 V DC / 30 V AC
Power Supply:12–24 V DC
Current Consumption:250 mA @ 24 V DC
Connectivity:Serial (RS‑232);
Mounting:Desk or panel mount with screw terminals
Enclosure Type:Indoor use; IP20 equivalent
Operating Temp:0 °C to +50 °C
Storage Temp:–40 °C to +85 °C
Humidity Limits:Up to 90–95% RH, non-condensing
Space requirements:4 TE, 3 HE (= 4 HP, 3U)
Power requirements: 5 V DC, 160 mA
Number of input channels: 16
Switch level: 1.4-1.9 mA
Hysteresis: 0.2 mA ± 0.05 mA
Input filter: First order, low pass 100Hz
Field wire resistance: Max. 50 Ω
output voltage 7.9-8.7 V
Channels:Typically 16 I/O
Output Types:Digital(0–10 VDC, 4–20 mA)
Analog Resolution:AI: 16‑bit; AO: 13‑bit
Power Supply:24 V DC nominal
Power Isolation:Galvanic isolation, reverse protection
Operating Temp:–40 °C to +70 °C
Enclosure / Rating:Up to IP66
Channels:Typically 16 I/O
Output Types:Analog (0–10 VDC, 4–20 mA)
Analog Resolution:AI: 16‑bit; AO: 13‑bit
Power Supply:24 V DC nominal
Power Isolation:Galvanic isolation, reverse protection
Operating Temp:–40 °C to +70 °C
Enclosure / Rating:Up to IP66
Medium: Multimode Dielectric Fiber 62.5/125
Wavelength:1300 nm
Maximum:Distance 2 km (1 mile)
Connector:MT-RJ
Voltage:3.3 V
Temperature Industrial:-40 C to +85 C (-40 F to +185 F)
Supply voltage: 24 V DC
Reset input voltage: 18 - 70 V DC
Reset input current: 1.1 mA at 24 V DC
Earth fault threshold: 5.5 mA (± 1 mA)
Max. earth current: 25 - 32 mA
Max. output current: 2 A
Isolation 1500 V DC / 1000 V AC
Initial contact resistance: 30 mW
Operating temperature: -5°C-+50°C (23°F-+122°F)
Max. output voltage: 36 V DC / 30 V AC
Power Supply Voltage:24 V DC ±10%
Power Consumption:4.5 W
Program Memory 32 kBytes
RAM (Data Memory):16 kBytes
Digital I/O Capacity:128 I/O max
Operating Temperature:0°C to +60°C
Storage Temperature:-25°C to +70°C
Humidity:5% to 95% (non-condensing)
Slots Available:5 module slots
Power Input:24 VDC
Operating Temperature:0°C to 60°C (32°F to 140°F)
Storage Temperature:-40°C to 85°C (-40°F to 185°F)
Humidity:5% to 95% RH, non-condensing
Power Supply Voltage:24 VDC
Power Consumption:< 5 Watts
Operating Temperature:-10°C to +55°C (14°F to 131°F)
Storage Temperature:-40°C to +70°C (-40°F to 158°F)
Humidity:5% to 95% non-condensing
Supply Voltage:24V DC
Power Consumption:< 2W
Isolation:500V AC
Operating Temp:-25°C to +70°C
Storage Temp:-40°C to +85°C
Humidity:5–95% (non-condensing)
Compact installation of I/O modules
Up to 16 channels of field signals
and process power connections
Connections to ModuleBus and I/O modules
Mechanical keying prevents
insertion of the wrong I/O module
Latching device to DIN rail for grounding
DIN rail mounting
Input Voltage: 24 VDC
Power Tolerance: Operates within ±10%
Analog Signals: 4–20 mA or 0–10 V
Operating Temperature: -25°C to +70°C
Humidity: ≤95% non-condensing
Voltage: Typically 24 VDC (±10%)
Power Consumption: <5–10 W
Digital Inputs: 8–16 channels
Analog Inputs: 4-20 mA/0-10 V
Temperature Range: -20°C to +70°C
Line monitored digital input
Non line monitored digital input
Line monitored ESD input (on Channel 32)
Analog input 0-20mA or 4-20mA
Digital output (0.5 Amp) configurable line monitoring
Multiple digital output (1 Amp or 2 Amp)
with or without line monitoring
Analog output 0-20mA or 4-20mA
DIGITAL INPUT MODULE
32 CHANNEL
24 VDC
ISOLATED
50 MA
PULSE WIDTH OUTPUT FUNCTION
TIME-PROPORTIONAL OUTPUT FUNCTION
STATUS DISPLAY
NO EXPLOSION PROTECTION
Number of input channels:64
Rated input voltage:24 V DC
Input ON voltage:20 to 26.4 V DC
Input OFF voltage :5.0 V DC or less
Input current :2.5 mA±20 % / channel
Maximum allowable input voltage:30.0 V DC
Input response time :8 ms or less
Minimum ON detection time:20 ms
Maximum ON/OFF cycle:25 Hz
Maximum current consumption:500 mA (5 V DC)
EC402 ESB Bus Coupler Module
5 Standard type with no explosion protection
E Standard type with explosion protection
0 Basic type
1 With ISA Standard G3 option
Operating Voltage:24 V DC
INVERTER MOTHERBOARD
FOR ACS580
3AXD50000716975
Input Voltage Range:380–500V AC (3-phase)
DC Bus Link:Integrated protection
Control Voltage:24V DC
Logic Board Power:Switch-mode PSU
Communication Isolation:1500V AC reinforced
Operating Temp:-15°C to +45°C
Input Voltage:380–690V AC
Output Power:up to 630 kW
Control Voltage:24V DC (±10%)
Ambient Operation:-15°C to +50°C
Humidity Protection:<95% non-condensing
CE Mark: Low Voltage Directive
Digital I/O: 6 programmable DI
Analog I/O: 2x 0–10V/4–20mA
Input Power (AC):400–690V (±10%) 3-phase
Motor Power Range:250kW–1.5MW
Control Voltage:Single-phase 26V DC to 30V DC (±15%)
Operating Temp:-15°C to +50°C
Harsh Environment:UL 1203
Busbar Terminals:values 8.9Nm ±0.5
AS-Interface Safety ATEX Gateway
Input Voltage:200–690V AC (-15%/+10%)
Power Range:15–400kW
Control Voltage:Single-phase 24V DC
Relay Outputs:4 × Form-A
AF-650PG: Profibus DP or CANopen
