PC BOARD
REFLECTIVE MEMORY
PCI NODE CARD
128 MBYTE MEMORY
MULTIMODE TRANSMISSION
Low Latency, Deterministic Transfer Rates
Operating System and Bus Structure Independence
Dual-port RS-232/RS-485
Baud rates up to 115.2 kbps
Voltage Levels: ±5V to ±15V
Max Cable Length: 15m (50 ft)
Supply Voltage: 24V DC (±10%)
Power Consumption: 3W typical
Power Supply: 28 VDC
Communication Ports: Ethernet, Serial
Operating Temperature: -40°C to +70°C
Storage Temperature: -55°C to +85°C
Humidity: 5–95% non-condensing
Series:90-30 PLC
Brand:GE Fanuc
Product Type:High-capacity power supply
Protocol Support:RS485
Nominal Rated Voltage:24VDC / 48VDC
Input Voltage Range, DC:Start: 21 to 56 VDC Run: 18 to 56 VDC
Voltage:24 Volts DC
Standard:UL, CE
Full load power rating:50 Watts
Velocity: 0–20 mm/s
Displacement: 0–500 µm
Frequency Range:10 Hz – 10 kHz
A/D Resolution:16-bit
Sampling Rate:Up to 50 kHz
Power Supply:24V DC
Power Consumption:5W typical
Accessory Boards:8 Boards
Ambient Temperature Rating:-30 to 65 Degrees Celsius
Base Circuitry Coating:Special Protection
Assembly Type:IS220 Standard Modular
Chassis Style:Rough Vented
Port Styles:2 Ethernet (Pictured)
Operating temperature: -30 to 65oC
Power Supply Voltage: 24 V dc
Number of channels: 6
Input span: 4-20 mA
Termination resistors: 121 Ohm
Technology: Surface Mount
Common Mode Voltage Range: ±5 V
Maximum Lead Resistance: 15Ω
Analog output current: 0-20 mA
Operating temperature: -30 to 65 °C
Operating Voltage:85–265V AC/DC
Nominal: 120/208V
Maximum: 690V AC
Burden: <0.2VA per phase
Standard CTs: 1A or 5A
Burden: <0.1VA at 5A
Voltage/Current: ±0.2% of reading
Power/Energy: ±0.5%
Frequency: ±0.01Hz
Input Voltage:24V DC (±10%)
Power Consumption:15W (typical)
Isolation Voltage:1500V AC
Analog Inputs:±10V
Control Bandwidth:1kHz (typical)
Resolution:16-bit
Update Rate:62.5μs (16kHz)
Series:Mark VI Speedtronic
Functional Acronym:BPPB
Input Voltage: 24V DC
Output Voltages:+5V DC @ 20A max
Efficiency: >90% typical
Ripple: <50mV p-p on all outputs
Multi-Voltage Power Distribution: Provides +5V, ±15V
Input Voltage:24 V DC
Output Voltage:±15 V DC or +5 V DC
Output Current:Up to 10 A
Power Rating:120–150 W
Efficiency:≥85% (typical)
Ripple & Noise:<1% of output voltage
Voltage Regulation:±1% (line and load)
Firing Angle Range:0–180°
Synchronization:3-phase AC input
Pulse Output:8–12 channels
Accuracy:±0.5° firing angle resolution
Isolation :2500V AC
Power Supply:+5V DC
Input Channels:32 optically isolated inputs
Input Type: 24–125V DC
Voltage Range:24V DC
Input Current :5–15mA per channel
Isolation :1500V AC
Response Time:≤10ms (ON/OFF)
Power Supply:+5V DC
Input Channels:3-phase voltage
Voltage Range:0–150V AC
Frequency Range:45–65Hz
Accuracy:±1% of full scale
Response Time:<2 cycles
Isolation:2500V AC
Power Supply:+5V DC
Supply Voltage: +24 V DC
Power Consumption: ≤15 W
Isolation Voltage: 1500 V AC
Voltage Range: 24–125 V DC
Current Rating: Up to 5 A per channel
Switching Speed: ≤10 ms
TRIP CONTROL CARD
PC BOARD SDCC MARK V SYSTEM
Analog Trip Signals: 4–20 m
Digital Trip Signals: 24 VDC
Aux Relay (K2): Alarm/status outputC
Resolution: 0.1% of setpoint
Accuracy: ±0.25% FS
Voltage: +24 VDC (±10%)
Consumption: 15 W (max)
Type:Scanner module
Speed:100 Mbps
Material:Multi-mode fiber (MMF)
Length:2 Kilometers
SD Card:Supported
Power:3.3 to 5 Volts
Port Connectors:Two RJ-45 and two SFP cages.
LED Indicators:Yes
Series: GE Mark VIe Series
Input Voltage: 24 V DC (±10%)
Power Consumption: ≤8 W
Voltage Range:0–30 V DC or 0–120 V AC
Range: 0–10 V DC, 4–20 mA
Resolution: 16-bit ADC
Type: Form-C contact relays (1 A at 30 V DC)
Operating Temperature: -40°C to +70°C
Relative Humidity: 5–95% (non-condensing)
Series: GE Mark VIe Series
Input: 24 V DC (±10%)
Isolation: ≥1.5 kV
Digital Inputs:0–30 V DC
Analog Resolution:16-bit ADC
Operating Temperature: -40°C to +70°C
Shock/Vibration: to 5 G (5–500 Hz)
Series: GE Mark VIe Series
Terminal Capacity: ≤32 AWG
Input Voltage: 24 V DC (±10%)
Power Consumption: <5 W
Galvanic Isolation: Up to 1.5 kV AC/DC
Voltage Range for Inputs: 0–120 V AC/DC
Digital Inputs (DI):30 V DC/120 V AC
Operating: -40°C to +70°C
Storage: -40°C to +85°C
Humidity Tolerance: 5–95% non-condensing
Series: GE Mark VIe
Dual Power Inputs: Isolated 24 V DC
Fail-safe relay contact rating: 2 A at 24 V DC
Input Voltage: 24 V DC (±10%)
Temperature Range: -40°C to +70°C (continuous operation)
Surge Protection: TVS diodes/SRC filters on I/O channels
Relative Humidity: 5–95% (non-condensing)
Operating Voltage:24 V DC ±10%
Power Consumption: <10 W
Types: 2-wire, 3-wire
Number of Inputs: 8 channels
Excitation Current:1 mA
Measurement Resolution: ≤0.1°C
Series: Mark VIe
Product Type: Relay Output Terminal Board
Number of channels: 16
Relay Type: SPDT
Relay Contact Rating: 10A
Input Voltage Range: 12V, 24V
Number of Relay Channels: 4, 8
Relay Switching Current: Max 10A
Mounting Type: DIN rail
Output Resolution: 12-bit
Output Impedance: 10 Ohm
Analog outputs: 0-20 mA
Series: GE Mark VIe
Input Voltage: 24 V DC (±10%)
Power Consumption: ≤15 W
Proximity Probes: 0–10 kHz
Accelerometers: Up to 20 kHz
IEPE sensor excitation:typically 18–24 V DC
Analog input: ±10 V peak
Operating Temperature: -40°C to +70°C.
Humidity Tolerance: 5–95% (non-condensing)
Input Voltage: 24 V DC (±10%)
Power Consumption: Typically <20 W
Sampling Rate:Up to 25.6 kS/s
Voltage ranges (analog): Typically ±10 V DC
Analog Input: 16-bit
Operating Temperature: -40°C to +70°C
Storage Temperature: -40°C to +85°C.
Relative Humidity: 5%–95% (non-condensing)
RX3I NIU WITH TWO SERIAL PORTS
20K OF LOCAL LOGIC
MODULE REQUIRES UNIVERSAL BASE (IC695CHSXXX)
REQUIRES ETHERNET MODULE (IC695ETM001)
NIU SUPPORTS ALL RX3I I/O MODULES
Analog Inputs: 4–8 channels
Analog Outputs: 4–20 mA or ±10 V DC
Digital I/O: 24 V DC
Form Factor: 6U VME module
Operating Temperature: -20°C to +70°C (-4°F to +158°F)
Humidity: 5–95% RH (non-condensing).
System: Mark VI Turbine Control System
Clock Speed: ≥1 GHz
RAM: 1–2 GB DDR3
Flash Storage: 4–8 GB
Form Factor: 6U VME module
Voltage: 24 V DC (±10%)
Power Consumption: ≤25 W
Analog: 4–20 mA, ±10 V DC
Digital: 24 V DC dry/wet contacts
Frequency: Vibration signals
Form Factor: 6U VME module
Data Acquisition:16-bit ADC resolution
Sampling rates up to 50 kS/s
Backplane: VME P1/J1 connectors for bus communication
Voltage Feedback: 0–500 V DC
Current Feedback: 0–10 A DC
Accuracy: ±0.25% of full scale
Frequency Response: Up to 100 Hz
Signal-to-System Isolation: 1500 V AC
Common-Mode Rejection: >60 dB at 50/60 Hz
Analog Output: 4–20 mA or 0–10 V DC
Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Outputs:3
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps
Application:Rx7i PLC System
Random Access Memory (RAM):64 MB
Operating Voltage:+5, +15, -12 Volt DC
Flash Memory:64 MB
Current Rating:3.4 Amps
Discrete I/O memory:32 K
Microprocessor:600 MHz Pentium M
Analog I/O memory:32 Kwords
CPU Memory:64 Megabytes
Compatible Memory storage:SRAM, Flash
User Memory:64 Megabytes
Processor speed:600 MHz
Max Program Block:512 Program Blocks
Series:PACSystem RX7i
Description:Power supply module
Part Number:IC698PSA100
Voltage:120/240 Volts AC, 125 Volts DC
Product Description:Power Supply module
Mounting:Leftmost slot
Input Voltage Range:85 to 264 VAC; 100-150VDC
Power Rating:125 Watts
Output Voltage:5/12, -12 Volts DC
AC Input Frequency:47-63 Hz
Power Factor:0.99 min
Manufacturer:GE Energy
Series:Mark VIe Wind
Part Number:IS210AEBIH3B
Functional Acronym:AEBI
Functional Description:Alternative Energy Bridge Interface
PCB Coating:Conformal Coating
AEBI:CARD GE WIND TURBINE
Input Voltage: 24V DC
Operating Temperature: Typically between -30°C to +65°C
Humidity: Typically 0-95% (non-condensing)
Series: EX2100
Product Type: Alternative Energy Application D
Number of channels: 6
Input Span: 1-5 V dc
Outputs: 24 V outputs
Technology: Surface Mount
Analog output current: 0-20 mA
Operating temperature: -30 to 65 °C
Input Channels:16 single-ended
Input Signal Types:4–20 mA current loops
Resolution:16-bit resolution
Accuracy:±0.1% of full-scale range
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity (non-condensing)
Input Channels:16 single-ended
Input Signal Types:4–20 mA current loops
Resolution:16-bit resolution
Accuracy:±0.1% of full-scale range
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity (non-condensing)
Input Voltage Range:24 VDC
Designed to support 24 VDC battery banks
Output Voltage:+5 VDC, ±15 VDC
Operating Temperature:-40°C to +70°C (-40°F to +158°F)
Humidity: Operates reliably at 5–95% relative humidity
Series: Mark VIe
Type: Wind Energy Main Cabinet Board
Input Voltage: Typically 24 VDC
Operating Temperature Range: -30°C to 65°C (-22°F to 149°F)
Storage Temperature Range: -40°C to 85°C (-40°F to 185°F)
Input Voltage: 24 VDC (nominal)
Output Voltage: 24 VDC (typically)
Output Current: 1-2A per relay
Relay Type: SPDT (Single Pole Double Throw) relays
Number of Relays: 8 (Typically, each with individual output terminals)
Relay Contact Rating:
Max Switching Voltage: 250 VAC or 30 VDC
Max Switching Current: 5A (AC or DC)
Max Switching Power: 120VA (AC) or 120W (DC)
Series:Genius Bus I/O
Part Number:IC697BEM731F
Operating Voltage:5.0 Volt DC
Backplane Current:1.3 Amps
Bus Cable:Belden 9182 type cable
Module Width:Single Slot
Description:Genius I/O Bus Controller
Application:IC66 PLC System
Location:IC66 PLC Rack
Connectors:3PL and 1PL Ports
LED Indicators:3 LED Indicators
Average Weight:2.0 Pounds
Series:PACSystem RX3i
Manufacturer:GE Fanuc
Part Number:IC694MDL645A
Rated Voltage:24 Volts DC (positive or negative logic)
No of Channels:Sixteen (16)
Input points:16 (1 group)
Wiring configuration:Positive / Negative Logic
Input Current:7 Milliamperes
Input signal range:0-30 VDC
Nominal Input voltage:24 VDC
Input current:7 mA per channel
Off state voltage:0 - +5 VDC
On state current:3.2 mA
Off state current:1.1 mA
On response time, typical:7 ms
On response time, maximum:7 ms
Product Lifecycle Status:Active
Series:PACSystem RX3i
Manufacturer:GE Fanuc
Part Number:IC694MDL645D
Rated Voltage:24 Volts DC (positive or negative logic)
No of Channels:Sixteen (16)
Input points:16 (1 group)
Wiring configuration:Positive / Negative Logic
Input Current:7 Milliamperes
Input signal range:0-30 VDC
Input Voltage Range:0 to 30 Volts DC
Nominal Input voltage:24 VDC
On State Voltage:11.5 - 30 VDC
Off state voltage:0 - +5 VDC
On state current:3.2 mA
Off state current:1.1 mA
On response time, typical:7 ms
On response time, maximum:7 ms
Product Lifecycle Status:Active
Series:Series 90-30
Manufacturer:GE Fanuc; Emerson Automation (Current)
Part Number:IC693MDL741
Product type:Digital I/O
Compatibility:GE Fanuc 90-30 PLCs
Product Description:Discrete output module
Output points:16
No of Channels:Sixteen (16)
Peak module current draw:110 milliamps
No. of output groups:Two (2)
Module voltage input:5 Volts DC
Channels per group:Eight (8)
Rated voltage:12/ 24 Volts DC
Peak output voltage drop:0.5 Volts
Nominal output voltage:12 / 24 VDC
On response time, maximum:2 ms
Off response time, maximum:2 ms
Output Voltage Drop:0.5 volts, maximum
Off-state Leakage:1 mA maximum
Functional Abbreviation:VCMI
Indicator LEDs:Run, Fail, Status, Reset
Instruction Manual:GEH-6421
OEM:GE Energy
Series:Mark VI Control System
Part Number:IS215VCMIH2C
Product Type:VME Communication Card
Brand:GE Fanuc
Series:Versamax
Part Number:IC200PWR001
Product Type:DC Power Supply
Input Voltage:24 Volts DC
Output Voltage:5 Volts DC and 3.3 Volts DC
Input Power:11 Watts
Holdup Time:10 Milliseconds
Total Output:1.5 A maximum
3.3V Output Current:0.25 A maximum
Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670GBI002D
Series:Field I/O control
Type:Bus interface unit
Part Number:IC670GBI002
CPU Redundancy:Supported
Supply Voltage range:18-30 VDC
Nominal supply voltage:24 VDC
Frequency:47 to 63 Hertz
Power consumption:16.8 Watts
Power Supply Output:6.5 VDC ±5%
Series:RX3i PacSystem
Part Number:IC695CPE330-AFAT
Product Type:CPU module
Processor Clock Speed:1.0 Ghz
RAM:64 MB
NVRAM:64MB
I/O Points:up to 32 K I/O
Controller Redundancy:Supported
Maximum Program Blocks:512
Maximum Block Size:128 kilobytes
